Bedienungsanleitung Panasonic AJ-SPC 700P (Seite 24 von 124) (Englisch)

597959

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Chapter 3 Recording and Playback (continued)

3-2 Basic Procedures

This section describes the basic procedure for shooting and

recording. Before you embark on a shoot, pre-inspect your

system to ensure that it works properly.

* For directions on inspecting your memory card camera-recorder,

see [7-1 Inspections Before Shooting].

Battery Set-up to P2 card Insertion

1 Insert a charged battery pack.

2 Turn on the POWER switch and ensure that more than

four segments of the battery-remaining amount

indication bar are illuminated.

z If the number of illuminated segments is fewer than

five, first check the battery placement. If placement is

not the problem, replace the battery with a fully

charged one.

3 Insert a P2 card and ensure that the P2 CARD

ACCESS LED stays on in orange or green. Then, close

the slide-out door.

When more than one P2 card slot contains a P2 card,

the card in the slot with the lowest number is used first.

However, regardless of slot number, a P2 card inserted

later will not be accessed until the other cards have

been used.

Example:

If all five slots contain P2 cards, the cards are used in

order of slot numbers 12345. However, if the

P2 card in Slot 1 is removed and then re-inserted, the

cards will be used in the following order:

23451.

Note that the recording order is retained even if the power is

turned off. When the power is next turned on, the last card

written before powering-down will be the target card.

<Note>

When “SLOT1” is selected for the menu option P.ON REC

SLOT SEL, recording starts from the P2 card inserted in the

smallest slot number, after the power is turned on.

This option is found in the REC FUNCTION screen on the

SYSTEM SETTING page.

Switch Setting

When a battery and P2 cards are installed, set the switches

as detailed below, before starting to use your AJ-SPC700P.

Setting the switches before shooting and recording

<Notes>

z The USER MAIN button is factory-set to perform the slot

selection function, which selects the target card from

among several P2 cards.

When a new target P2 card is selected, the appropriate

slot number appears on the P2 card remaining amount

indicator in the viewfinder.

For more information about the indications in the

viewfinder, see [4-7-2 Viewfinder Status Indication

Layout].

z SLOT SEL function is enabled during recording; however,

a few seconds are required for switching slots. When the

target P2 card is switched during recording, further

switching to a different P2 card cannot be accepted for

over ten seconds after the first switch.

z The ability to switch to a different target P2 card using the

SLOT SEL function is not available over ten seconds after

recording starts.

z When a Voice Memo is recorded simultaneously with the

video and sound, video and sound recording continues

after switching of the target P2 card using the SLOT SEL

function; however, Voice Memo recording stops.

12345

OUTPUT:

CAM/AUTO KNEE ON

AUDIO SELECT

CH 1/CH 2:

AUTO

Iris: Auto

TCG:

F-RUN or

R-RUN

GAIN:

Normally, this should be set to 0 dB. If

conditions are too dark, an

appropriate gain level should be set.

USER MAIN:

This switch is factory-set to

perform slot selection.

#,52%2'PINKUJDQQMࡍ࡯ࠫ㧞㧜㧜㧢ᐕ㧡᦬㧝㧝ᣣޓᧁᦐᣣޓඦ೨㧥ᤨ㧠㧡ಽ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic AJ-SPC 700P Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info