Bedienungsanleitung Panasonic BL-C101 (Seite 1 von 2) (Englisch)

628278

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

1. Insert the included CD-ROM into your PC.

• The Setup Program starts. If the program does not start, double-click Setup.exe found

on the CD-ROM.

2. Click [Search for Cameras].

• The program searches for cameras connected to your network.

If [Windows cannot open this file] is displayed after clicking [Manual]

[Select the program from a list]→[OK]→Check [Always use the selected program to open this

kind of file]→[Browse]→Browse to [C:\WINDOWS\system32\mshta.exe]→[Open]→[OK]

3. When the Windows Security Alert is displayed, click

[Unblock].

• If the dialog is not displayed, continue to the next step.

4. Select the camera you want to configure, and click

[Access Camera].

• To assign all network settings to the camera manually, or to assign an IP address using

the DHCP feature of your router, click [Network Settings], then select [Specify an IP

Address] or [DHCP] and enter the appropriate settings.

5. Enter the desired user name and password, then click

[Save].

• Do not forget the user name and password you set here, otherwise you will need to

reset the camera and configure it again.

6. Enter the user name and password, then click [OK].

7. For BL-C121 Only:

Click [Next] to configure the camera’s wireless

settings, enter the wireless settings, then click [Save].

• These settings are not available for the BL-C101, continue to the next step.

• BL-C121 users can skip this step by selecting [Disable] and then clicking [Next].

Wireless settings will not be configured.

• [About this program]: Displays the program’s version

information.

• [Search for Cameras]: Displays a list of cameras

connected to your network.

• [Manual]: Allows you to view the included

documentation. PDF versions of the printed

documentation are included on the CD-ROM; Adobe

Reader

is required to view them.

• [Update Firmware]: Allows you to use the Setup

Program to update the camera’s firmware (built-in

software).

• [Save Settings to PC/Save Settings to Camera]:

Allows you to save a backup of all camera settings on

your PC, or restore all settings in the camera using a

backup file saved on your PC.

• [Network Camera Recorder with Viewer Software

Single Camera Version Installation]: Installs the

[Network Camera Recorder with Viewer Software

Single Camera Version] software. (See “Installing the

Network Camera Recorder with Viewer Software

Single Camera Version” on page 2.)

• [Exit]: Closes the screen and exits the Setup Program.

• If you have more than one camera, you can

distinguish cameras by model number,

printed on the front of the camera, or by

MAC address (see “Camera Diagrams” on

page 2 in the Installation Guide to find your

camera’s MAC address label).

• If more than 20 minutes have passed since

the selected camera was turned on, you

cannot configure the camera. Turn off the

camera, then turn it on again. This

restriction does not apply to cameras which

have not been configured yet or have been

reset to their factory default settings.

• If you are using firewall or antivirus software on your PC, the Setup Program may not

be able to find any cameras on your network. If you cannot disable your firewall or

antivirus software, you can configure the camera by entering its MAC address (see

“Camera Diagrams” on page 2 in the Installation Guide to find your camera’s MAC

address label).

If you are using a French, German, Italian,

Spanish, Russian, Simplified Chinese, or

Japanese language OS, this screen will be

displayed in the corresponding language,

and all subsequent camera screens will be

displayed in that language.

• Configure the camera for wireless

access by configuring the

corresponding camera settings to

match the wireless settings of your

wireless router. For more information,

refer to the operating instructions

included with your wireless router, and

to 5.3.1 Configuring the Camera for

Wireless Connection (BL-C121 Only) in

the Operating Instructions on the CD-

ROM.

Before Reading this Document

This manual is written for both the BL-C101 (Wired Type) and BL-C121

(Wireless/Wired Type). Available features and operations vary slightly

depending on the model. You can confirm the model no. of your camera by

checking the model no. printed on the front of the camera.

Model number suffixes (“A”, “CE”, and “E”) are omitted from the following

model numbers shown in this document, unless necessary.

BL-C101A, BL-C101CE, BL-C101E, BL-C121A, BL-C121CE, BL-C121E

Make sure you have read the Important Information document and

followed the instructions in the Installation Guide for connecting your

camera.

• Before following the instructions in this document:

– Confirm that your camera is turned on and connected to your router.

– Temporarily disable any firewall or antivirus software on your PC.

– Close your web browser.

• Screenshots shown in this document are for reference only and may vary from what is

displayed on your PC depending on the camera model, network settings, etc.

Abbreviations

• UPnP is the abbreviation for “Universal Plug and Play”.

• The Network Camera is referred to as “the camera” in this document.

• The Setup CD-ROM is referred to as “the CD-ROM” in this document.

Trademarks

• Adobe and Reader are either registered trademarks or trademarks of Adobe Systems

Incorporated in the United States and/or other countries.

• Microsoft, Windows, Windows Vista, Windows Server, ActiveX, and Internet Explorer are

either registered trademarks or trademarks of Microsoft Corporation in the United States

and/or other countries.

• Screen shots reprinted with permission from Microsoft Corporation.

• All other trademarks identified herein are the property of their respective owners.

• This software is based in part on the work of the Independent JPEG Group.

Setup Guide

Network Camera

Model No.

BL-C101

(Wired Type)

BL-C121

(Wireless/Wired Type)

PNQX1567YA KK0908CM1020

Please read this document before using the product, and save this document for future

reference.

Panasonic Network Camera Website:

http://panasonic.net/pcc/products/netwkcam/

Indoor Use Only

8. When [Setup completed] is displayed, click [To Single

Camera page].

• If the following ActiveX

Controls dialog is displayed, click [Install ActiveX Control...].

• When the following Security Warning is displayed, click [Install].

• The camera image is displayed.

• Screen content varies by model number.

9. Click the [Setup] tab, click [Date and Time] on the left

side of the screen, then set the camera’s date and

time. Click [Save] when finished.

• Screen content varies by model number.

To configure the camera for access from the Internet or from a mobile

phone, continue with the following steps.

Note:

• In order to configure the camera for access over the Internet using these instructions, your

router must be UPnP

™

compatible and must have its UPnP

™

feature turned on (it is turned

off by default on most routers). For more information, refer to the operating instructions

included with your router.

• To configure the camera for access over the Internet using a router that does not support

UPnP

™

, refer to Section 4 Configuring the Camera for Access from the Internet in the

Operating Instructions on the CD-ROM for general information, and refer to the operating

instructions included with your router.

• Disable the maximum idle time setting on your router if you have a PPPoE or PPTP

connection to your Internet Service Provider.

1. Click the [Internet] tab at the top of the camera screen.

2. Select [Enable] under [Auto Port Forwarding (IPv4)],

select [Register with Viewnetcam.com] under

[Viewnetcam.com Registration], then click [Save].

• When the dialog about the camera’s port number changing is displayed, click [OK].

• The camera and router will begin configuring themselves via UPnP

™

• If you select to register with Viewnetcam.com, click [Go to Viewnetcam.com

Registration page] when it is displayed. The Viewnetcam.com website will open

automatically. Follow the on-screen instructions to register.

3. When [Setup completed] is displayed, click [To Single

Camera page].

• If you enabled [Auto Port Forwarding (IPv4)], the camera’s port number may have

changed. Do not forget the addresses displayed here.

• To confirm that the camera can be accessed from the Internet using a PC, use a PC

not connected to your network and access the camera using the address displayed

here.

• The IP address or URL used to access the camera over the Internet will also be

displayed on the [Status] page of the [Maintenance] tab.

After configuring the camera’s wireless settings, confirm that the

camera can be accessed wirelessly.

1. Disconnect the LAN cable from the camera, and

unplug the AC adaptor from the power outlet.

2. Set the WIRELESS/WIRED switch on the side of the

camera to WIRELESS.

3. Plug the AC adaptor in to the power outlet.

• Confirm that the indicator lights green after about 1 minute. If the indicator does not

light green, see 1.2 Camera Indicator Issues in the Troubleshooting Guide on the CD-

ROM.

4. Start your web browser and access the camera.

• Enter camera’s IP address that was displayed during setup, then press [Enter] on the

keyboard.

• If you cannot access the camera, see 1.4 Wireless Connection Issues (BL-C121 Only)

in the Troubleshooting Guide on the CD-ROM.

• You may need to restart your router in order to access the camera in wireless mode.

The camera’s IP address is displayed. This is the

IP address you must enter in your web browser to

access the camera. Do not forget this address.

This will install the viewer program (ActiveX

Controls) needed to display camera images

properly. Viewer programs must be installed to

view MPEG-4 images, MJPEG images, and to use

audio features.

Congratulations! You have successfully set up the

camera and can now view camera images.

For more information, refer to 5.5 Setting the Date

and Time in the Operating Instructions on the CD-

ROM.

Setup is complete. To configure the camera for access from the

Internet, see “Access from Internet Configuration”. To confirm the

camera’s wireless connection (BL-C121 only), see “Confirming

Wireless Connection (BL-C121 Only)”.

If you are finished setting up the camera, return to the Installation

Guide and follow the instructions for mounting the camera.

Access from Internet Configuration

If you are interested in accessing your camera over

the Internet, we recommend using

Viewnetcam.com. Viewnetcam.com is a Dynamic

DNS service designed for use with Panasonic

Network Cameras, and is provided free of charge.

For more information about Viewnetcam.com,

refer to the Viewnetcam.com website

(http://www.viewnetcam.com) for information

about this service.

The camera’s IP addresses for local (LAN) and

Internet access are displayed. These are the IP

addresses you must enter in your web browser to

access the camera over the LAN or from the

Internet. Do not forget these addresses.

Setup is complete. To confirm the camera’s wireless connection

(BL-C121 only), see “Confirming Wireless Connection (BL-C121

Only)”.

If you have any difficulty accessing the camera or viewing camera

images, refer to the Troubleshooting Guide on the CD-ROM,

otherwise return to the Installation Guide and follow the

instructions for mounting the camera.

Confirming Wireless Connection (BL-C121 Only)

If you are finished setting up the camera, return to the Installation

Guide and follow the instructions for mounting the camera.

Installing the Network Camera Recorder with Viewer Software Single Camera Version

The CD-ROM includes a single camera version of the Panasonic Network Camera Recorder with Viewer Software. Click [Manual] on the Network Camera Setup Program window for details about

the installation and operation of this software.

1. Insert the included CD-ROM into your PC.

• The Setup Program starts. If the program does not start, double-click Setup.exe found on the CD-ROM.

2. Click [Network Camera Recorder with Viewer Software Single Camera Version Installation].

3. Follow the on-screen instructions to install the software.

4. When installation is complete, double-click the shortcut icon on your desktop to start the software.

Note:

• Network Camera Recorder with Viewer Software Single Camera Version is compatible with Microsoft

Windows Vista

, Windows

XP and Windows Server

2003.

• Camera registration is limited to one camera.

• Support is not provided for the single camera version of this software.

Panasonic BL-C101 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic BL-C101

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info