Bedienungsanleitung Panasonic DMP-BD35 (Seite 39 von 48) (Englisch)

456584

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

RQT9243 or RQT9350

TV screen and video Page

Sound

The images from this unit

do not appear on the

television.

Picture is distorted.

Jittering occurs.

≥ Make sure that the television is connected to either the VIDEO OUT terminal,

COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on this unit.

≥ Make sure that the television’s input setting (e.g., VIDEO 1) is correct.

≥ An incorrect resolution is selected in “Component Video Resolution”, when the

television is connected to COMPONENT VIDEO OUT terminals. While stopped,

press and hold [∫] and [1] (PLAY) on the main unit at the same time for more

than 5 seconds to cancel this setting. Set the item again.

≥ If “24p Output” is set to “On” when the unit is connected to a TV through any

terminal other than HDMI, images may not display properly. In this case, set “24p

Output” to “Off”.

≥ When “24p Output” is set to “On”, HDMI authentication takes place where 24p

images switch to other images, and a black screen is displayed.

≥ When “24p Output” is set to “On”, jittering may occur while playing DVD-Video

other than 24p images. In this case, turn “24p Output” to “Off”.

≥ [DivX]: Images may not be output due to how files were created.

≥ Press [∫] and [1] (PLAY) simultaneously on the unit for more than 5 seconds to

shift to more compatible mode with HDMI equipment. However, Dolby Digital

Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream. To output the

bitstream, select “Restore Default Settings” to restore the factory presets and

make proper settings.

≥ Picture may not be seen when more than 4 devices are connected with HDMI

cables. Reduce the number of connected devices.

—

The screen changes

automatically.

≥ When the “Screen Saver Function” in the Setup menu is set to “On”, the display

may return to the screen saver mode automatically if there is no operation for

10 minutes or more.

Video is not output in high

definition.

≥ High definition video cannot be output through the VIDEO OUT terminals.

≥ Confirm that the “HDMI Video Mode”, “HDMI Resolution”, and “Component Video

Resolution” in the Setup menu are set properly.

—

The 4:3 aspect ratio picture

expands left and right.

Screen size is wrong.

≥ Use the television to change the aspect. Refer to your television’s operating

instructions.

≥ When using a component video cable, set “Progressive” to “Video”. If the situation

is not restored after that, set “TV Aspect” to “4:3 Pan & Scan”.

≥ When using an HDMI cable, change “TV Aspect” type to “16:9”.

—

29, 32

There is a lot of after-image

when playing video.

≥ Turn “3D NR” or “Integrated NR” off if it is on. 29

When playing DVD-Video

using progressive output,

one part of the picture

momentarily appears to be

doubled up.

≥ When you use the HDMI AV OUT terminal for video output, follow the steps below

for setting.

1 Connect this unit to the TV with any cable except the HDMI cable.

2 When you connect with the Component Video cable, set “HDMI Video Mode” to

“Off” and “Component Video Resolution” to “480i” in the Setup menu.

Still pictures (JPEG) do not

playback normally.

≥ The images that were edited on the PC, such as Progressive JPEG, etc., may not

playback.

No sound.

Low volume.

Distorted sound.

Cannot hear the desired

audio type.

≥ Check the connections and the “Digital Audio Output” settings. Check the input

mode on the amplifier/receiver if you have connected one.

≥ Press [AUDIO] to select the audio.

≥

[BD55]: When the unit is connected to an amplifier/receiver with the AUDIO OUT

terminal, set “Analog Audio Output” and match multi channel speaker settings. If

these are not set properly, the audio is not output correctly.

≥

[BD55]: When connected to an amplifier/receiver or any other devices using both

AUDIO OUT terminal and HDMI AV OUT terminal, the audio from AUDIO OUT

terminal may not be output with the desired audio depending on the specifications

of the connected devices, etc. Set “HDMI Audio Output” to “Off”, when you output

multi-channel surround sound from AUDIO OUT terminal.

≥ The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream

signal is output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT

terminal.

≥

[DivX]: Audio may not be output depending on how files were created.

≥ Audio may not be heard when more than 4 devices are connected with HDMI

cables. Reduce the number of connected devices.

≥ To output audio from a device connected with an HDMI cable, set “HDMI Audio

Output” to “On” in the Setup menu.

11–13, 31

32, 34

—

Cannot switch audio. ≥ There are discs for which audio cannot be changed because of how the disc was

created.

≥ When connecting an amplifier/receiver using a coaxial cable (

[BD55]), optical

digital audio cable or an HDMI cable, you cannot switch the audio if “Dolby D/

Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” is set to “Bitstream”. Set “Dolby D/

Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “PCM” or connect using AUDIO

OUT terminal.

—

12, 13, 31

Reference

DMP-BD55_35PP-RQT9243_ENG.book 39 ページ２００８年８月２９日　金曜日　午前１０時２８分

Panasonic DMP-BD35 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic DMP-BD35

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info