Bedienungsanleitung Panasonic DMP-BD35 (Seite 34 von 44) (Englisch)

456584

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

RQT9245

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and

use.

On the television Page

Authorisation Error.

This unit is not authorised to

play this title.

≥[DivX] You are trying to play the DivX VOD content that was purchased with a different

registration code. You cannot play the content on this unit.

Cannot play. ≥You inserted an incompatible disc. 4, 5

Cannot play on this unit. ≥You tried to play a non-compatible image.

≥Confirm “SD” on the unit’s display is not blinking and re-insert the card.

5, 22

—

No disc is inserted. ≥The disc may be upside down. —

Rental Expired. ≥[DivX] The DivX VOD content has zero remaining plays. You cannot play it. 20

$ This operation is currently

disabled.

≥Some operations are prohibited by the unit or disc. For example;

– [BD-V]

: During play back, reverse slow-motion or reverse frame-by-frame is not possible.

– Depending on the disc, you may not be able to perform search or skip when film previews

and warning screens are being played back.

—

Cannot connect.

Please check the connection of

the LAN cable.

≥When a hub is used but its Link lamp does not light up, check the cable connection, LAN

terminal connection, cable itself (a cross cable may be used by mistake), etc.

IP address is not set. ≥The “IP Address” in “IP Address / DNS Settings” is “---. ---. ---. ---“. Set the “IP Address”,

“Subnet Mask”, and “Gateway Address“. (Select the automatic address acquisition if

necessary.)

Cannot obtain IP address.

Please check the connection or

setting of the router.

≥If you use a hub, then check the connection between the hub and the router.

– Use the UPLINK port of the hub to connect to a router.

– Check whether or not the hub’s Link lamp lights up. If it does not light up, then check the

cable connection, LAN terminal connection, cable itself (a cross cable may be used by

mistake), etc.

≥If the above conditions are OK, then the router may not operate in DHCP mode. Check the

router settings and operation. You may reset the router to restore it to normal.

This IP address is already in

use.

Please check the setting.

≥This unit’s IP address is used by another device. Check the IP addresses of this unit,

personal computers, and routers, etc. If necessary, reconfigure them to avoid IP addresses

from being duplicated.

—

Connection test could not be

conducted.

≥Turn the unit off. Remove the AC mains lead and reconnect it and try again. If the same

symptom persists, then consult your dealer.

—

IP address is not set correctly.

Connection test was

unsuccessful. No reply from

Gateway. Please check the

connection or setting of the

router.

≥If you use a hub, then check the connection between the hub and the router.

– Use the UPLINK port of the hub to connect to a router.

– If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal

connection, cable itself (a cross cable may be used by mistake), etc.

≥Check the “IP Address”, “Subnet Mask”, and “Gateway Address” in the “IP Address / DNS

Settings”.

≥If the MAC address information is required, then press [SETUP] to display the “Network

Settings” menu.

Network connection was

rejected.

Please confirm Setup “BD-Live

Internet Access”.

≥When you set “BD-Live Internet Access” to “Limit” and play BD-Live contents which do not

have a content owner certificate, the Internet access of the content is not allowed. If you

allow the content to connect to Internet, set “BD-Live Internet Access” to “Permit”.

On the unit’s display

F99 ≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to standby

for 3 seconds. Now press [Í/I] on the main unit again to turn the unit on.

—

HDMI ONLY ≥Some BD-Video discs can only be output with HDMI. —

No PLAY ≥There is a viewing restriction on a BD-Video or DVD-Video. 26

No READ ≥The disc is dirty or badly scratched. The unit cannot play. —

PLEASE WAIT ≥The unit is carrying out internal process.This is not a malfunction. You cannot operate the

unit while “PLEASE WAIT” is displayed.

—

SET 

(“  ” stands for a number.)

≥The remote control and main unit are using different codes. Change the code on the

remote control.

Press and hold [OK] and the indicated number button at the same

time for more than 5 seconds.

UNFORMAT ≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or

DVD-RW (DVD-Video format).

—

UNSUPPORT ≥You have inserted a disc the unit cannot play. 4, 5

U59 ≥The unit is hot.

The unit switches to standby for safety reasons. Wait for about 30 minutes until the

message disappears.

Select a position with good ventilation when installing the unit. Do not block the cooling fan

on the rear of the unit.

—

U72

U73

≥The HDMI connection acts unusually.

– The connected equipment is not HDMI compatible.

– Please use HDMI cables that have the HDMI logo (as shown on the cover).

– The HDMI cable is damaged.

—

DMP-BD55&35EB&EG&EF-RQT9245_eng.book 34 ページ２００８年８月２２日　金曜日　午後６時５４分

Panasonic DMP-BD35 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic DMP-BD35

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info