Bedienungsanleitung Panasonic DMP-BD84 (Seite 30 von 38) (Englisch)

734646

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

- 30 -

Reference

Troubleshooting guide

Before requesting service, please perform the

following checks.

If the problem remains unresolved, consult

your dealer for instructions.

∫ Unit does not respond to remote

control or unit’s buttons.

Disconnect the AC mains lead, wait 1 minute,

then reconnect the AC mains lead.

The following do not indicate a problem with

this unit:

– Regular disc rotating sounds.

– Image disturbance during search.

∫ Cannot eject disc.

1 Turn the unit on.

2 Press and hold [OK], the yellow button and

the blue button on the remote control at the

same time for more than 5 seconds.

4 Press [OK].

To return to the factory defaults.

¾ Select “Yes” in “Default Settings” in the Setup

menu. (> 29)

To return all settings to the factory preset.

¾ Reset the unit as follows:

1 Turn the unit on.

2 Press and hold [OK], the yellow button and

the blue button on the remote control at the

same time for more than 5 seconds.

4 Press and hold [OK] for more than 5 seconds.

The remote control does not work properly.

¾ Change the batteries in the remote control.

(> 5)

¾ The remote control and this unit are using

different codes.

Press and hold [OK] and the displayed

number (“”) for more than 5 seconds.

The TV tuner mode is not displayed when the

TV is turned on.

¾ This phenomenon may occur, depending on

the TV setting, when “Quick Start” is set to

“On”.

¾ Depending on the TV, this phenomenon may

be prevented by reconnecting the HDMI cable

to a different HDMI input terminal or by

changing the HDMI auto connection setting.

This unit is turned off automatically.

¾ To save on electricity, this unit is turned off

automatically if there is no button operation

for about 20 minutes when not playing back

(such as when paused or displaying the

menu, displaying still pictures, etc.).

You have forgotten your ratings password.

You want to cancel the ratings level.

¾ The ratings level returns to the factory

defaults.

1 Turn the unit on.

2 Press and hold [OK], the yellow button and

the blue button on the remote control at the

same time for more than 5 seconds.

4 Press [OK].

Do you have the latest firmware installed?

Panasonic is constantly improving the unit’s

firmware to ensure that our customers are

enjoying the latest technology. (> 14)

–

[BDT281/280] [BDT185/184/181/180] [BDT168/167] Image

disturbance when replacing 3D discs.

– POWER LED starts to flash, and “00 RET”

is displayed on the screen.

3 Press [1] (right) repeatedly on the remote

control until “06 FTO” is displayed on the

screen.

General operation

– POWER LED starts to flash, and “00 RET”

is displayed on the screen.

3 Press [1] (right) repeatedly on the remote

control until “08 FIN” is displayed on the

screen.

Turn on this unit by using the standby/on

switch on this unit, and check “Remote

control ”, which is displayed on the screen

when you press a button on the remote

control.

– POWER LED starts to flash, and “00 RET”

is displayed on the screen.

3 Press [1] (right) repeatedly on the remote

control until “03 VL” is displayed on the

screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic DMP-BD84 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic DMP-BD84

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info