Bedienungsanleitung Panasonic DMP-BD901 (Seite 27 von 36) (Englisch)

546107

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SQT0108

SettingsReference

Reference

Troubleshooting guide

Before requesting service, please perform the

following steps.

∫ Unit does not respond to remote

control or unit’s buttons.

Disconnect AC power supply cord, wait 1 minute,

then reconnect AC power supply cord.

The following do not indicate a problem with

this unit:

– Regular disc rotating sounds.

– Image disturbance during search.

∫ Cannot eject disc.

1 Turn the unit on.

2 Press and hold [OK], the yellow button and

the blue button on the remote control at the

same time for more than 5 seconds.

– POWER LED starts to flash, and “00RET” is

displayed on the screen.

3 Press [1] (right) repeatedly on the remote

control until “06FTO” is displayed on the

screen.

4 Press [OK].

To return to the factory defaults.

¾ Select “Yes” in “Restore Default Settings” in

the Setup menu. (> 26)

To return all settings to the factory preset.

¾ Reset the unit as follows:

1 Turn the unit on.

2 Press and hold [OK], the yellow button and

the blue button on the remote control at the

same time for more than 5 seconds.

– POWER LED starts to flash, and “00RET” is

displayed on the screen.

3 Press [1] (right) repeatedly on the remote

control until “08FIN” is displayed on the

screen.

4 Press and hold [OK] for more than 5 seconds.

The remote control does not work properly.

¾ Change the batteries in the remote control.

(> 5)

¾ The remote control and this unit are using

different codes. Turn on this unit by using the

standby/on switch on this unit, and check

“Remote control ” which is displayed on the

screen when you press a button on the

remote control.

Press and hold [OK] and the displayed

number (“”) for at least 5 seconds.

The TV tuner mode is not displayed when the

TV is turned on.

¾ This phenomenon may occur, depending on

the TV setting, when “Quick Start” is set to

“On”.

¾ Depending on the TV, this phenomenon may

be prevented by reconnecting the HDMI cable

to a different HDMI input terminal or by

changing the HDMI auto connection setting.

You have forgotten your ratings password.

You want to cancel the ratings level.

¾ The ratings level returns to the factory

defaults.

1 Turn the unit on.

2 Press and hold [OK], the yellow button and

the blue button on the remote control at the

same time for more than 5 seconds.

– POWER LED starts to flash, and “00RET” is

displayed on the screen.

Press

[1]

(right) repeatedly

on the remote

control

until “

03 VL

” is displayed on the screen.

4 Press [OK].

Do you have the latest firmware installed?

Panasonic is constantly improving the unit’s

firmware to ensure that our customers are

enjoying the latest technology. (> 12)

Make the following checks and visit our

website for more information.

For U.S.A. :

www.panasonic.com/support

Enter the model number.

For Canada :

http://www.panasonic.ca

Or visit our website to find a service center.

You can find a service center near you easily

on our website.

Other support information:

“Customer Services Directory (United States

and Puerto Rico)” (> 33) or “CONTACT

INFORMATION” (> 34).

General operation

DMP-BD91_81_SQT0108_eng.book 27 ページ２０１３年１２月３日　火曜日　午前１０時５０分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic DMP-BD901 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info