Bedienungsanleitung Panasonic DMP-UB900 (Seite 39 von 44) (Englisch)

641954

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

- 39 -

Reference

When using wireless LAN connection, video

from the DLNA Certified media server is not

played back or video frames are dropped

during playback.

¾ Higher transfer rate router such as 802.11n

(2.4 GHz or 5 GHz) wireless router may solve

the problem. If you use 802.11n (2.4 GHz or

5 GHz) wireless router, it is necessary to set

the encryption type to “AES”.

Simultaneous use with a microwave, cordless

telephone etc. at 2.4 GHz may result in

connection interruptions or other problems.

¾ On the “Wireless Settings” screen (> 32), the

continuous lighting of at least 4 “Reception”

indicators is the target for a stable connection.

If 3 or fewer indicators are lit or the

connection is being interrupted, change the

position or angle of your wireless router and

see if the connection state improves. If there

is no improvement, connect to a wired

network and perform the “Easy Network

Setting” (> 17) again.

Cannot read. Please check the disc.

¾ You inserted an incompatible disc.

Cannot play this title.

¾ You tried to play a non-compatible image.

No disc inserted.

¾ The disc may be upside down.

$ This operation cannot be performed now.

¾ Some operations are unsupported by the unit.

(For example, reverse slow motion, etc.)

IP address is not set.

¾ The “IP Address” in “IP Address / DNS

Settings” is “---. ---. ---. ---”. Set the “IP

Address”, “Subnet Mask”, and “Gateway

Address”. (Select the automatic address

acquisition if necessary.)

The wireless access point currently has a low

network security setting. It is recommended to

change to a higher setting.

¾ Set a stronger network security level referring

to the wireless router operating instructions.

F99

¾ The unit fails to operate properly. Touch [Í/I]

on the main unit for 3 seconds to switch the

unit to standby, then switch back on.

NET

¾ While connecting to a network.

NO PLAY

¾ There is a viewing restriction on a BD-Video

or DVD-Video. (> 33)

NO READ

¾ The media is dirty or badly scratched. The

unit cannot play.

REMOVE

¾ The USB device is drawing too much power.

Remove the USB device.

SET CODE 

(“  ” stands for a number.)

¾ The remote control and this unit are using

different codes. Change the code on the

remote control.

Press and hold

[OK] and the

indicated number

button at the same time for more than

5 seconds.

U59

¾ Temperature of this unit is hot and the unit

switches to standby for safety reasons.

Wait for about 30 minutes.

Install or place this unit with good ventilation.

START

¾ A firmware update will start. Please do not

turn off the unit.

UPDATE /5

(“  ” stands for a number.)

¾ A firmware update is in progress.

Please do not turn off the unit.

FINISH

¾ The firmware update is complete.

Messages on the screen

Messages on the unit’s display

DMP-UB900_EG-SQW0698.book 39 ページ２０１６年３月７日　月曜日　午前１１時４６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic DMP-UB900 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic DMP-UB900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info