Bedienungsanleitung Panasonic DMP161EG (Seite 29 von 36) (Englisch)

602940

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

- 29 -

Reference

The TV screen turns black.

¾ In the following cases, HDMI authentication

takes place and a black screen is displayed:

– When “24p Output” is set to “On”.

– [BDT260] [BDT161] [BDT160] When the display

is switched between 2D and 3D images.

This unit does not recognize the USB

connection correctly.

¾ Disconnect and re-connect the USB cable. If

it still does not recognize the connection, turn

this unit off and on again.

¾ USB devices may not be recognized by this

unit when connected using the following :

– a USB hub

¾ If you connect USB HDD to this unit, use the

USB cable that is supplied with the HDD.

The images from this unit do not appear on

the TV.

Picture is distorted.

¾ An incorrect resolution is selected in “HDMI

Video Format”. Reset the setting as follows:

1 Turn the unit on.

2 Press and hold [OK], the yellow button and

the blue button on the remote control at the

same time for more than 5 seconds.

– POWER LED starts to flash.

Set the item again. (> 24)

– When Dolby Digital Plus, Dolby TrueHD,

and DTS-HD

audio are not output properly,

select “Yes” in “Default Settings” (> 27) and

make proper settings.

Video is not output in high-definition.

¾ Confirm that “HDMI Video Format” in the

Setup menu is set properly. (> 24)

– a USB extension cable other than the

supplied with the Wireless LAN Adaptor

DY-WL5 (optional)

Picture

3 Press [8] and the blue button on the remote

control at the same time for more than

5 seconds.

¾ The unit and TV are using different video

systems.

1 Turn the unit on.

2 Press and hold [OK], the yellow button and

the blue button on the remote control at the

same time for more than 5 seconds.

– POWER LED starts to flash, and “00RET”

is displayed on the screen.

3 Press [1] (right) repeatedly on the remote

control until “05P/N” is displayed on the

screen.

4 Press and hold [OK] for more than

5 seconds.

The system switches from PAL to NTSC or

vice versa.

¾ PAL discs cannot be correctly viewed on an

NTSC TV.

¾ [BDT260] [BDT161] [BDT160] When “3D

BD-Video Playback” in the Setup menu is set

to “Automatic”, images may not be output

depending on the connection method. After

removing the disc from this unit, select “Set

before play” in the Setup menu, and select

“2D Playback” in the setup screen displayed

when playing 3D discs. (> 25)

3D video is not output.

[BDT260] [BDT161] [BDT160]

¾ Connect to a full high-definition TV.

¾ Is there a non-3D compatible amplifier/

receiver connected between this unit and a

TV? (> 9)

¾ Are the settings on this unit and the TV

correct? (> 17)

¾ Is the amplifier/receiver that is connected

between this unit and TV on?

¾ Depending on the connected TV, the video

being played back might switch to 2D video

due to changes in resolution etc. Check the

3D setting on the TV.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic DMP161EG Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic DMP161EG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info