Bedienungsanleitung Panasonic DMPBD45 (Seite 30 von 40) (Englisch)

602954

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

VQT2J95

ReferenceReference

Troubleshooting guide

Before requesting service, please perform the

following steps.

The following do not indicate a problem with this unit:

≥ Regular disc rotating sounds.

≥ Image disturbance during search.

∫ Unit doesn’t respond to remote control

or front panel buttons.

Press and hold [Í/I] on the main unit for 3 seconds.

– If still unable to turn the unit off, disconnect the AC mains

lead, wait 1 minute, then reconnect the AC mains lead.

∫ Cannot eject disc.

The unit may have a problem.

1 While the unit is off, press and hold [OK], the yellow

button and the blue button on the remote control at the

same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2 Repeatedly press [1](right) on the remote control or [Í/I]

on the unit until “06 FTO” is displayed on the unit's

display.

3 Press [OK] on the remote control or [< OPEN/CLOSE] on

the unit.

To return to the factory preset.

Select “Yes” in “Default Settings” in the Setup menu. (

29)

To return all settings to the factory preset.

Reset the unit as follows:

1 While the unit is off, press and hold [OK], the yellow

button and the blue button on the remote control at the

same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2 Repeatedly press [1](right) on the remote control or [Í/I]

on the unit until “08 FIN” is displayed on the unit's display.

3 Press and hold [OK] on the remote control or [< OPEN/

CLOSE] on the unit for at least 3 seconds.

Power of this unit is turned off when the input

for the TV is switched.

This is a normal phenomenon when using VIERA Link

(HDAVI Control 4 or later). For details please read the

operating instructions for the TV.

The remote control doesn’t work properly.

The remote control and main unit are using different

codes. If “SET 1”, “SET 2” or “SET 3” is displayed when a

button is pressed on the remote control, change the code

on the remote control. (> 29)

It may be necessary to set the manufacturer code or the

remote control code again after changing the batteries for

remote control. (> 14)

The TV tuner mode is not displayed when the

TV is switched on.

This phenomenon may occur, depending on the TV

setting, when “Quick Start” is set to “On”.

– Depending on the TV, this phenomenon may be prevented

by reconnecting the HDMI cable to a different HDMI input

terminal or by changing the HDMI auto connection setting.

You have forgotten your ratings password.

You want to cancel the ratings level.

The ratings level returns to the factory preset.

1 While the unit is on, press and hold [OK], the yellow

button and the blue button on the remote control at the

same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2 Repeatedly press [1] (right) on the remote control or [Í/

I] on the unit until “03 VL” is displayed on the unit's

display.

3 Press [OK] on the remote control or [< OPEN/CLOSE] on

the unit.

Do you have the latest firmware installed?

Firmware updates may be released to correct operating

irregularities that are discovered with certain movies.

(> 14)

Make the following checks.

If the problem remains unresolved, consult

your dealer for instructions.

General operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic DMPBD45 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic DMPBD45

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info