Bedienungsanleitung Panasonic DMPBDT110EG (Seite 38 von 42) (Englisch)

603029

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

VQT3B63

Messages

The following messages or service numbers appear on the

television or unit’s display when something unusual is

detected during startup and use.

Cannot play.

You inserted an incompatible disc.

Cannot play on this unit.

You tried to play a non-compatible image.

Confirm “SD” on the unit’s display is not displayed and

re-insert the card.

No disc is inserted.

The disc may be upside down.

$ This operation is not available.

Some operations are unsupported by the unit. For

example;

– BD-Video: During playback, reverse slow-motion or

reverse frame-by-frame is not possible.

IP address is not set.

The “IP Address” in “IP Address / DNS Settings” is “---.

---. ---. ---”. Set the “IP Address”, “Subnet Mask”, and

“Gateway Address”. (Select the automatic address

acquisition if necessary.)

The wireless access point currently has a low

network security setting. It is recommended to

change to a higher setting.

Authentication type for the Wireless LAN is set to “Open

system”, or the encryption type is set to “No encryption”.

It is recommended to encrypt for safety reasons. For

details, refer to the instructions of the Wireless router

being used. Encryption is required when playing back

video, etc., from DLNA compatible devices.

F99

The unit fails to operate properly. Press [Í/I] on the

main unit for 3 seconds to switch the unit to standby,

then switch back on.

HDMI ONLY

Some BD-Video discs can only be output with HDMI.

NET

While connecting to a network.

No PLAY

There is a viewing restriction on a BD-Video or

DVD-Video. (> 30)

No READ

The media is dirty or badly scratched. The unit cannot

play.

PLEASE WAIT

The unit is carrying out internal process. This is not a

malfunction. You cannot operate the unit while “PLEASE

WAIT” is displayed.

REMOVE

The USB device is drawing too much power. Remove

the USB device.

SET 

(“  ” stands for a number.)

The remote control and main unit are using different

codes. Change the code on the remote control.

Press and hold [OK] and the

indicated number button at the

same time for more than 5 seconds.

U59

The unit is hot.

The unit switches to standby for safety reasons. Wait for

about 30 minutes until the message disappears.

Select a position with good ventilation when installing the

unit. Do not block the ventilation hole on the side of the

unit.

H or F

(“  ” stands for a number.)

There is something unusual.

Check the unit using the troubleshooting guide. If the

service number does not disappear, do the following.

1 Disconnect the plug from the household mains socket

wait a few seconds, then reconnect it.

2 Press [Í/I] to turn the unit on. (The unit may be fixed.)

If the service number does not disappear despite doing the

above, request service from the dealer. Inform the dealer of

the service number when requesting service.

START

The system is being restarted during the firmware

update. Please do not turn off the unit.

UPD/

(“  ” stands for a number.)

The firmware is being updated.

Please do not turn off the unit.

FINISH

The firmware update is complete.

On the television

On the unit’s display

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic DMPBDT110EG Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic DMPBDT110EG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info