Bedienungsanleitung Panasonic EY0L32 (Seite 11 von 200) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

568599

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

NOTE for

EY7430

• The clutch delivers different levels

of torque based on the location,

material, and type of the screw. Be

sure to check these before starting.

• Due to the way the product is

constructed, you may sometimes not

be able to set it to drill mode after

operating the clutch. This does not

mean the product is broken. When

this happens, set the clutch to (1) and

rotate a few times.

• When loosening the screws, adjust

the torque position to “

”.

Model No: EY7430 & EY7530

Speed Selection for

EY7430

Choose 1 (LOW) or 2 (HIGH) speed to

suit the use.

【 Fig.6 】

The more the variable speed control

trigger is pulled, the higher the speed

becomes.

CAUTION:

• Check the speed selector switch

before use.

• Use at low speed when high torque

is needed during operation. (Using

at high speed when high torque

is required may cause a motor

breakdown.)

• Do not operate the speed selector

switch [1 (LOW)- 2 (HIGH)] while

pulling on the speed control

trigger. This can cause the

rechargeable battery to wear

quickly or damage the internal

mechanism of the motor.

* See specifications for “ MAXIMUM

RECOMMENDED CAPACITIES ”.

• Continued operation with the

speed control trigger held down

can cause electric parts to break

and the tool to stop working.

NOTE:

• Always use the low speed [1 (LOW)]

when drilling large holes with a wood

drill bit or a hole saw.

Switch and Forward/Reverse Lever

Operation

【 Fig.4 】 for

EY7430

【 Fig.7 】 for

EY7530

CAUTION:

To prevent damage, do not operate

Forward/Reverse lever until the bit

comes to a complete stop.

Forward Rotation Switch Operation

1. Push the lever for forward rotation.

2. Depress the trigger switch slightly to

start the tool slowly.

3. The speed increases with the amount

of depression of the trigger for efficient

tightening of screws and drilling .

The brake operates and the chuck

stops immediately when the trigger is

released.

4. After use, set the lever to its center

position (switch lock).

Reverse Rotation Switch Operation

1. Push the lever for reverse rotation.

Check the direction of rotation before

use.

2. Depress the trigger switch slightly to

start the tool slowly.

3. After use, set the lever to its center

position (switch lock).

NOTE:

The drill will stop if the Forward/Reverse

lever is pushed while the trigger is

held down.This will happen even if

the Forward/Reverse lever is pushed

accidentally.

You will not be able to hold the trigger

down again until you release it and

return the Forward/Reverse lever to its

original position.

Clutch Torque Setting for

EY7430

Adjust the torque to one of the 17 clutch

settings or “

” position.

【 Fig.5 】

CAUTION:

Test the setting before actual

operation.

EY7530_7430_3732_0L32_02(Eng).indd 11 2014/08/18 15:40:52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY0L32 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info