Bedienungsanleitung Panasonic EY3640 (Seite 10 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

502388

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is

inserted into the AC power supply, but this

is not a problem in terms of safety.

2. Insert the battery pack firmly into the

charger. (Fig. 15)

1. Line up the alignment marks and

place the battery onto the dock on

the charger.

2. Slide forward in the direction of the

arrow.

3. During charging, the charging lamp will

be lit.

When charging is completed, an internal

electronic switch will automatically be

triggered to prevent overcharging.

• Charging will not start if the battery

pack is warm (for example,

immediately after heavy-duty

operation).

The orange standby lamp will be

flashing until the battery cools down.

Charging will then begin automatically.

4. The charge lamp (green) will flash

slowly once the battery is approximately

80% charged.

5. When charging is completed, the

charging lamp will start flashing quickly

in green color.

6. If the temperature of the battery pack

is0°Corless,chargingtakeslongerto

fully charge the battery pack than the

standard charging time.

Even when the battery is fully charged,

it will have approximately 50% of the

power of a fully charged battery at

normal operating temperature.

7. If the power lamp does not light

immediately after the charger is plugged

in, or if after the standard charging time

the charging lamp does not flash quickly

in green, consult an authorized dealer.

8. If a fully charged battery pack is

inserted into the charger again, the

charging lamp lights up. After several

minutes, the charging lamp may flash

quickly to indicate the charging is

completed.

Ni-MH/Ni-Cd Battery Pack

NOTE:

When you charge the battery pack for

the first time, or after prolonged storage,

charge it for about 24 hours to bring the

battery up to full capacity.

Battery charger (EY0L80)

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is

inserted into the AC power supply, but this

is not a problem in terms of safety.

2. Insert the battery pack firmly into the

charger. (Fig. 16)

3. During charging, the charging lamp will

be lit.

When charging is completed, an internal

electronic switch will automatically be

triggered to prevent overcharging.

• Charging will not start if the battery

pack is warm (for example,

immediately after heavy-duty

operation).

The orange standby lamp will be

flashing until the battery cools down.

Charging will then begin automatically.

4. When charging is completed, the

charging lamp will start flashing quickly

in green color.

5. If the charging lamp does not light

immediately after the charger is plugged

in, or if after the standard charging time

the charging lamp does not flash quickly

in green, consult an authorized dealer.

6. If a fully charged battery pack is

inserted into the charger again, the

charging lamp lights up. After several

minutes, the charging lamp may flash

quickly to indicate the charging is

completed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY3640 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info