Bedienungsanleitung Panasonic EY4542 (Seite 19 von 212) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

502392

Zoom out

Zoom in

Vorherige Seite

1/212

Nächste Seite

Note for the battery symbol

(bottom two symbol examples):

This symbol might be used in combination with a

chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical

involved.

. MAINTENANCE

WARNING

To avoid severe personal injury, always remove

the battery pack from the tool before starting any

maintenance procedure.

CAUTION:

To assure product SAFETY and RELIABILITY,

servicing should be performed by an autho-

rized service center. Always insist on genuine

Panasonic replacement parts.

Cleaning Tool

Keep your tool clean for good cutting perform-

ance, and to help keep it safe to use.

Follow these steps:

1. Remove the battery pack from the tool.

2. Wipe the tool with a dry, soft cloth. Do not

use a wet cloth or cleaning liquids.

They could damage the tool’s finish.

3. Be sure to rub off any oil or grease which

could make the tool slippery or hard to handle.

4. Remove the blade and brush off any dust.

CAUTION:

To avoid injury or damage to the unit, never

immerse any part of the tool in a liquid.

Transparent Guard

WARNING

If the guard is cracked, or is broken, take the tool

to an authorized service center for replacement.

Do not attempt to operate tool. It could result in

serious personal injury.

Never use your tool with a damaged transparent

guard or without the transparent guard installed.

Flying chips could result in serious injury.

. ACCESSORIES

WARNING

• The use of any accessories not specified

in this manual may result in fire, electric

shock, or personal injury. Use recommended

accessories only.

• Use of a blade on material that is thicker

or thinner than that recommended for that

blade will result in a rough cut, and could

increase the risk of “kickback” or other injury.

Carbide-tipped Blade for Metal

• EY9PM13C

For cutting unhardened ferrous material

Thickness of material

0.5 mm – 6.0 mm (1/32" – 1/4")

Carbide-tipped Blade for Thin Metal (Optional

accessory)

• EY9PM13D

For cutting unhardened thin ferrous thin material

that clean cutting edge required

Thickness of material

0.5 mm – 6.0 mm (1/32" – 1/4")

Carbide-tipped Blade for Wood (Optional

accessory)

• EY9PW13A

For cutting wood in general

Carbide-tipped Blade for Thin Wood (Optional

accessory)

• EY9PW13B

For cutting thin wood that clean cutting edge

required

Recommended thickness of material up to 12

Carbide-tipped Blade for Plastic (Optional

accessory)

• EY9PP13B

For cutting plastic

Recommended thickness of material acrylic

and vinyl chloride plates:

2.0 mm – 5.0 mm (5/64" – 3/16")

corrugated pates, pipes

0.8 mm – 5.0 mm (1/32" – 3/16")

Vacuum hose adaptor (Optional accessory)

• EY9X012E

Rip Fence (Optional accessory)

• EY3500B7727

For convenience of rip cuts and repeated cut of

uniform width

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY4542 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info