Bedienungsanleitung Panasonic EY45A2 (Seite 9 von 176) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

568605

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

•

Never use other than the dedicated charger

to charge the battery pack. Otherwise, the

battery may leak, overheat, or explode.

•

After removing the battery pack from the

tool or the charger, always reattach the pack

cover. Otherwise, the battery contacts could

be shorted, leading to a risk of fire.

•

When the Battery Pack Has Deteriorated,

Replace It with a New One.

Continued use of a damaged battery pack

may result in heat generation, ignition or bat-

tery rupture.

III

. ASSEMBLY

Attaching or Removing Battery

Pack

CAUTION:

Before inserting battery pack, check that the

power switch in the tool actuates properly and

returns to the “OFF” position when released.

1. To connect the battery pack (See Fig. 2)

Align the highlighted marker points and attach

battery pack.

• Slide the battery pack until it locks into posi-

tion.

Alignment

marks

Fig. 2

2. To remove the battery pack (See Fig. 3)

Push down the button and slide the battery

pack forward.

Button

Fig. 3

. OPERATION

Before Using the Tool

This tool is intended to cut unhardened fer rous

metal, nonferrous metal, wood, and plastic.

Refer to the “Accessories” section for a list of

blades to be used for the proper applications

of this tool. The following precautions must be

followed to reduce the risk of injury;

• Do not cut stacked materials. Cut one piece at

a time.

• Do not cut hardened steel.

• Cut materials with the wider edge of the shoe

over the clamped side of the material.

• Do not touch the saw blade, workpiece, or cut-

ting chips with bare hands immediately after

cutting; they may be hot and could burn skin.

Each time you use the tool, you must make sure

it is in good operating condition.

Use the following checklist:

1. Is the blade installed in the correct direction?

The arrow on the blade must point in the same

direction as the arrow on the upper blade

cover.

2. Is the blade installed properly?

Make sure the hex bolt is tightened securely.

(See Fig. 6)

3. Does the blade look alright?

Replace the blade immediately if there are

any cracks in it or if any teeth are broken.

4. Does the lower guard close properly?

WARNING

To avoid injury, do not use the tool if the lower

guard does not close quickly over the blade.

5. Is the transparent guard securely installed?

6. Is the battery pack charged and inserted

firmly to the tool?

7. Is the depth adjustment nut for cutting secure-

ly tightened?

8. Is the workpiece securely clamped on a saw

horse or bench?

9. Is the dust case or front cover clogged with

dust?

10. Only use the blade rated at higher speed

than that of main unit.

The blade may be damaged if the blade is

used under the rated speed of the main unit.

Disengage the front cover lock button and

remove any dust that has become clogged in-

side the cover. If the cover is clogged, use a long

object such as a manual screwdriver to unclog it.

After doing so, close the front cover. (See Fig. 4)

EY45A2(EU).indb 9 2014-1-15 10:13:08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY45A2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info