Bedienungsanleitung Panasonic EY7549 (Seite 15 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

502429

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

CAUTION:

• The built-in LED light is designed to

illuminate the small work area tem-

porarily.

•

Do not use it as a substitute for a

regular

flashlight, since it does not

have enough brightness

• LED light turn off when the tool has

not been used for 5 minutes.

Caution : DO NOT STARE INTO BEAM.

Use of controls or adjustments or performance

of procedures other than those speciﬁ ed herein

may result in hazardous radiation exposure.

(2) Overheat warning lamp

Off

(normal

operation)

Illuminated:

Overheat

(motor)

Flashing:

Overheat

(battery)

Indicates operation has

been halted due to motor

or battery overheating.

To protect the motor or battery, be

sure to note the following when

carrying out this operation.

• If the motor or battery becomes

hot, the protection function will be

activated and the motor or battery

will stop operating. The overheat

warning lamp on the control panel

illuminates or flashes when this

feature is active.

• If the overheating protection feature

activates, allow the tool to cool

thoroughly (at least 30 minutes).

The tool is ready for use when the

overheat warning lamp goes out.

• Avoid using the tool in a way that

causes the overheating protection

feature to activate repeatedly.

• If the tool is operated continuously

under high-load conditions or if it is

used in hot-temperature conditions

(such as during summer), the

overheating protection feature may

activate frequently.

• If the tool is used in cold-temperature

conditions (such as during winter) or

if it is frequently stopped during use,

the overheating protection feature

may not activate.

• The ambient temperature range

is between 0°C (32°F) and 40°C

(104°F).If the battery pack is used

when the battery temperature is

below 0°C (32°F), the tool may fail to

function properly.

• When charging a cool battery pack

(below 0°C (32°F)) in a warm place,

leave the battery pack at the place

and wait for more than one hour to

warm up the battery to the level of

the ambient temperature.

• The performance of the EY9L42

deteriorates significantly at and below

10°C due to work conditions and

other factors.

(3) Battery low warning lamp

Off

(normal

operation)

Flashing

(No charge)

Battery protection

feature active

Excessive (complete) discharging

of lithium ion batteries shortens their

service life dramatically. The driver

includes a battery protection feature

designed to prevent excessive dis-

charging of the battery pack.

• The battery protection feature acti-

vates immediately before the bat-

tery loses its charge, causing the

battery low warning lamp to flash.

• If you notice the battery low warning

lamp flashing, charge the battery

pack immediately.

• If it is started with too little battery

power remaining, the tool may stop

operating without the battery low

warning lamp flashing first. This

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY7549 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info