Bedienungsanleitung Panasonic EYFLA1A (Seite 10 von 168) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

502434

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

NOTE:

• All 3 bars on the battery indication lamp

will flash when the automatic power-off

function is activated.

•

When the battery indication lamp begins

flashing, the battery pack should be

charged (or replaced with a fresh unit)

immediately.

•

Be sure to fully charge the battery pack

in question after activation of the auto-

matic power-off function. Failure to do

so may prevent the automatic power-off

function from being properly deactivated.

(3) The torque control function

• The torque control function calculates the

load from the motor’s rotational angle during

the hammer impact and determines that the

bolt has been properly seated when a pre-

set load value is exceeded. Driving is then

automatically stopped after a preset number

of impacts have been delivered to the bolt.

CAUTION:

•

Always check the tool’s tightening torque

before use. Improper tool operation may

result in excessive or inadequate tight-

ening.

CAUTION:

•

Always operate the tool with the switch

fully engaged. The torque control func-

tion will not operate when the switch is

not sufficiently engaged, preventing the

tool from stopping automatically.

•

In work where a heavy load comes to

bear during tightening, the load may be

interpreted as the seating of the bolt,

preventing the bolt from being com-

pletely tightened.

•

Repeated tightening of the same bolt

may break the bolt or deform the mate-

rial into which the bolt is being driven as

a result of excessive tightening.

•

The tightening torque value and preci-

sion vary with factors such as the mate-

rial into which the bolt is being driven

and the condition of the socket being

used. Adjust the torque as necessary

for the work being performed. Bolt tight-

ening torque varies due to the factors

described below.

1) Bolt

•

Bolt diameter: Tightening torque gener-

ally increases with bolt diameter.

•

Torque coefficient (indicated by the bolt

manufacturer), grade, length, etc.

) Other

• Bit and socket condition: Material,

amount of play, etc.

•

Use of a universal joint or socket

adapter

•

User: Manner in which the tool is

applied to the bolt, strength with which

the tool is held, manner in which the

tool’s switch is engaged

•

Condition of object being tightened: Ma-

terial, seating surface finish

Setting the tool to configuration mode

Turn off the control panel.

• If the control panel is on, remove and

then reinsert the battery pack.

Engage the switch while pushing the

button and then release both the

but-

ton and the switch.

•

After all the LED lamps have turned off,

the control panel will flash and change

to configuration mode.

NOTE:

• Tools ship from the factory set to “F”

mode (torque control function off).

•

The control panel will turn off if the tool

is not operated for a period of 5 min-

utes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EYFLA1A Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info