Bedienungsanleitung Panasonic EYFMA1 (Seite 10 von 56) (Englisch, Französisch, Spanisch)

568594

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

(2) The battery indication lamp

• Use the battery indication lamp to check

how much power is left in the battery.

•

Battery life varies slightly with ambient tem-

perature and battery characteristics. The

lamp is designed to provide a rough indica-

tion of remaining battery life.

Battery indication lamp

Indicator Battery status

Fully charged

Approx. 40% or less

remaining

Flashing

Approx. 20% or less

remaining (indicates need

to recharge battery)

The battery pack will need

to be charged soon.

Flashing

No charge

The battery pack needs to

be charged.

(The tool’s automatic

power-off function will

activate at this stage.)

Automatic power-off function

• The automatic power-off function is designed

to prevent a loss of tightening torque due to

reduced battery voltage. Once it has been

activated, the tool will not operate until the

battery pack has been charged (or replaced

with a fresh unit), even if the trigger is

depressed.

Battery indication lamp

Indicator

Flashing

NOTE:

• All 3 bars on the battery indication lamp

will flash when the automatic power-off

function is activated.

•

When the battery indication lamp begins

flashing, the battery pack should be

charged (or replaced with a fresh unit)

immediately.

•

Be sure to fully charge the battery pack

in question after activation of the auto-

matic power-off function. Failure to do

so may prevent the automatic power-off

function from being properly deactivated.

(3) The torque control function

• The torque control function calculates the

load from the motor’s rotational angle during

the hammer impact and determines that the

bolt has been properly seated when a pre-

set load value is exceeded. Driving is then

automatically stopped after a preset number

of impacts have been delivered to the bolt.

CAUTION:

•

Always check the tool’s tightening

torque before use. Improper tool opera-

tion may result in excessive or inad-

equate tightening.

CAUTION:

•

Always operate the tool with the switch

fully engaged. The torque control func-

tion will not operate when the switch is

not sufficiently engaged, preventing the

tool from stopping automatically.

•

In work where a heavy load comes to

bear during tightening, the load may be

interpreted as the seating of the bolt,

preventing the bolt from being com-

pletely tightened.

•

Repeated tightening of the same bolt

may break the bolt or deform the mate-

rial into which the bolt is being driven as

a result of excessive tightening.

•

The tightening torque value and preci-

sion vary with factors such as the mate-

rial into which the bolt is being driven

and the condition of the socket being

used. Adjust the torque as necessary

for the work being performed. Bolt tight-

ening torque varies due to the factors

described below.

1) Bolt

•

Bolt diameter: Tightening torque gener-

ally increases with bolt diameter.

•

Torque coefficient (indicated by the bolt

manufacturer), grade, length, etc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EYFMA1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info