Bedienungsanleitung Panasonic KX-TCA115EXC (Seite 42 von 77) (Englisch)

463426

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

15.3. Telephone Line Interface

Bell signal detection

Clip signal detection

ON/OFF hook circuit

Audio circuits

Bell & Clip (: Calling Line Identification Presentation: Caller ID) signal detection:

In the standby mode, Q2 is open to cut the DC loop current and decrease the ring load.

When ring voltage appears at the TP3 (A) and TP40 (B) leads (when the telephone rings), the signal is transferred as follows;

A → C4 → R2 → R29 → IC2 (DLP) [BELL & CLIP]

B → C3 → R1 → R30 → IC2 (DLP) [BELL & CLIP]

ON/OFF hook circuit:

In the standby mode, Q2 is open, and connected as to cut the DC loop current and to cut the voice signal. The unit is

consequently in an off-hook condition.

When IC2 detects a ring signal or press the TALK Key onto the handset, Q3 turns on and then Q2 turns on, thus providing an

off-hook condition (active DC current flow through the circuit) and the following signal flow is for the loop current.

A → D2 → Q2 → R8 → Q6 → R19 → R20 → D2→ B[OFF HOOK]

Audio circuits:

Refer to SIGNAL ROUTE (P.46).

15.4. Transmitter/Receiver

Base Unit and Handset mainly consist of RF Module and DECT BBIC.

Base Unit and Handset transmit/receive voice signal and data signal through the antenna on carrier frequency.

Signal Path:

*Refer to SIGNAL ROUTE (P.46).

15.4.1. Transmitter Block

The voice signal input from the TEL LINE interface goes to RF Module (IC3) through DECT BBIC (IC2) as shown in BLOCK

DIAGRAM (BASE UNIT) (P.39)

The voice signal passes through the analog part of IC2 where it is amplified and converted to a digital audio stream signal. The

burst switch controller processes this stream performing encryption and scrambling, adding the various other fields to produce

the GAP (Generic Access Profile) standard DECT frame, assigning to a time slot and channel etc.

In IC3, the carrier frequency is changing, and frequency modulated RF signal is generated and amplified, and radiated from

antenna. Handset detects the voice signal or data signal in the circuit same as the following explanation of Receiver Block.

15.4.2. Receiver Block

The signal of 1.9 GHz band (1.881792 GHz ~ 1.897344 GHz) which is input from antenna is input to IC3 as shown in BLOCK

DIAGRAM (BASE UNIT) (P.39).

In IC3, the signal of 1.9 GHz band is demodulated, and goes to IC2 as GAP (Generic Access Profile) standard DECT frames.

It passes through the decoding section burst switch controller where it separates out the frame information and performs de-

encryption and de-scrambling as required. It then goes to the DSP section where it is turned back into analog audio. This is

amplified by the analog front end, and goes to the TEL LINE Interface.

15.5. Pulse Dialling

During pulse dialing the hookswitch (Q4,Q5) is used to generate the pulses using the HOOK control signal, which is set high

during pulses. To force the line impedance low during the “pause” intervals between dial pulses, the PULSE_DIAL signal turns

on Q12.

KX-TCD150FXB / KX-TCD150FXC / KX-TCD152FXB / KX-TCA115EXB / KX-TCA115EXC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic KX-TCA115EXC Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info