Bedienungsanleitung Panasonic KX-TG454 (Seite 19 von 96) (Englisch)

588766

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Link to cell settings

Selecting which unit receives

ellular calls

You can select which unit rings and receives

calls for a cellular line. When “All” is

selected, all handsets and the base unit ring.

1 For CELL 1: MMENUN#6271

For CELL 2: MMENUN#6272

2 MbN: Select the desired handset or “All”.

a MSAVEN

3 MOFFN

Note:

R When you select a specific handset to

receive calls for a cellular line:

– other handsets cannot answer the calls.

– the base unit can answer the calls even

though it does not ring. However, you

can make the base unit ring by adjusting

the base unit ringer volume (page 39).

(KX-TGE270 series: page 3)

R When you change the setting to “All”, the

base unit ringer volume also returns to the

lowest level even if the ringer volume has

been changed.

R The units selected with this setting have the

text message alert feature (page 53)

applied to them.

Ring as cell mode

nce this feature is turned on, the handset

and base unit ring using the same ringer tone

as your cellular phone.

The following settings are available:

– “Off”: Turn this feature off to use the

ringer tones of the handset and base unit.

Caller information is announced depending

on the Talking Caller ID setting (page 41).

– “On (with Talking CID)” (default):

The handset and base unit use your cellular

phone’s ringer tone. Caller information is

announced even if the Talking Caller ID is

turned off.

– “On (without Talking CID)”: The

handset and base unit use your cellular

phone’s ringer tone. Caller information is

not announced even if the Talking Caller ID

s turned on.

Important:

R To use this feature, your cellular phone

must support Bluetooth in-band ringtone.

Refer to your cellular phone’s operating

instructions.

1 For CELL 1: MMENUN#6141

For CELL 2: MMENUN#6142

2 MbN: Select the desired setting.

3 MSAVEN a MOFFN

Note:

R The units use the preset ringer tones

(page 41) instead of your cellular phone’s

ringer tone when a cellular call is being

received if:

– your cellular phone is in silent mode

(depending on your cellular phone).

– the base unit is in use.

– 2 handsets are sharing a landline call.

R If your cellular phone is in silent mode with

“On (with Talking CID)” set, the unit

announces caller information even when

Talking Caller ID is turned off (page 41).

To use the handset ringer tone

nstead of your cellular phone’s

ringer tone

Select “Off” in step 2, “Ring as cell mode”,

page 19.

To change the handset ringer tone for a

cellular line, see page 39.

Auto connection to the Bluetooth

evices (cellular phones or

headset)

After pairing, your Bluetooth devices are

connected to the base unit. If you move the

Bluetooth devices out of base unit range, the

Bluetooth devices are disconnected from the

base unit. This feature allows the base unit to

try to reconnect the Bluetooth devices at

regular intervals when it returns within base

unit range. You can set the interval. The

default setting is “1 min”.

For assistance, please visit http://www.panasonic.com/help

Link to Cell

TGE26x_27x(en)_1216_ver041.pdf 19TGE26x_27x(en)_1216_ver041.pdf 19 2013/12/16 19:32:272013/12/16 19:32:27

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic KX-TG454 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info