Bedienungsanleitung Panasonic KXTCD440 (Seite 30 von 40) (Englisch)

39160

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

30 Helpline Tel. No. :U.K. 08700 100 076 R.O.I. 01289 8333

Multi-unit Operation

Operating additional units

Additional handsets

Up to 6 handsets can be registered to a

single base unit. Additional handsets will

give you the freedom to, for example, have

an intercom call with another handset while

a third handset is on an outside call. See

page 3 for information on ordering additional

handsets.

Additional base units

Handsets can be registered to up to 4 base

units, allowing you to add additional base

units and extend the area in which your

handset(s) can be used. If a handset moves

out of range of its base unit when “AUTO” is

selected on base unit selection (page 31), it

will look for another base unit to make or

receive calls. A base unit and the handsets

it communicates with is called a “radio cell”.

Note:

L Calls will be disconnected when the

handset moves from one radio cell to

another.

L Intercom calls and call transfers are only

possible between handsets in the same

radio cell.

Registering a handset to a

base unit

To register an additional handset to a

base unit (easy registration)

The included handset and base unit are

preregistered. After purchasing an

additional handset, register it to the base

unit using the following method.

1 Lift the additional handset and press

{ih}.

2 Press and hold {x} on the left side of the

base unit for about 5 seconds, until the

registration tone sounds.

3 Place the additional handset on the base

unit. The registration tone continues to

sound. With the handset still on the base

unit, wait until a confirmation tone sounds

and w stops flashing.

Note:

L If an error tone sounds, or if w is still

flashing, register the handset manually

(manual registration).

L If all registered handsets start ringing in

step 2, press {x} to stop, then start again.

L Charge the batteries of your additional

handset for about 7 hours before initial

use.

To register a handset to an additional

base unit (manual registration)

You can register a handset to a base unit

manually using the following method.

1 Press {j}.

2 Press {v} repeatedly to display

“SETTING HS”, then press {>}.

3 Press {v} repeatedly to display

“REGISTRATION”, then press {>}.

4 Press {v} repeatedly to display

“REGISTER HS”, then press {>}.

5 Press and hold {x} on the left side of the

base unit for about 5 seconds, until the

registration tone sounds.

L After pressing {x}, the rest of the

procedure must be completed within

1 minute.

6 Press {v} repeatedly to select a base

unit number, then press {>}.

7 Wait until “BS PIN” is displayed, then

enter “0000” (default base unit PIN).

L If you changed PIN, enter it (page 22).

8 Press {>}.

L When the handset has been registered

TCD440_445E.book Page 30 Friday, February 27, 2004 4:22 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic KXTCD440 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info