Bedienungsanleitung Panasonic MC-CG 461 (Seite 19 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

459800

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

D - MAINTENANCE AND SERVICING

Indicator for replacing the dust bag

Turn the power control to the highest setting and lift the nozzle

off the ﬂoor. If the dust indicator turns red, the dust bag is full

and requires replace the dust bag.

NOTE: If the dust bag is not properly installed, the cover will

not close. Be sure to check that the bag is properly

installed before operating, otherwise dust will leak out.

The dust bag can easily lay on the dust cover packing or

clip between bag collar and body, so be sure to properly

extend it into the vacuum cleaner body.

Replacing the dust bag

D-1 Lift dust cover catch and raise dust cover until it

clicks properly.

D-2 Remove bag collar from bag holder and pull out dust

bag.

D-3 Set the dust bag.

D-4 Close dust cover.

Floor nozzle

D-5 Inspect once a month.

Using an old toothbrush or similar tool, clean any dirt or

lint from the brush.

Turbine nozzle

D-6 After removing the brush cover with a coin, remove the

beater bar from the belt.

Then cut across threads, strings, hairs, etc. from the

beater bar with a pair of scissors. (Removal as per

reverse procedure)

NOTE: Take care not to cut the brush.

Do not wash in water.

Vacuum cleaner body

D-7 Wipe with a soft cloth soaked with water.

Maintaining the Pre-motor Filter

Perform the procedure given below when the suction power is

not restored after maintaining the ﬁlter.

D-8 Open the dust cover.

D-9 Remove the pre-motor ﬁlter.

D-10 Wash gently with water and then allow to dry in a

shaded location.

D-11 Replace to its original location.

NOTE: Make sure you remember to replace the ﬁlter. If the ﬁlter

is not installed, it will cause motor failure.

• Do not wash the ﬁlter in a washing machine or dry it with a

dryer or other source of hot air.

CAUTIONS

• The plug must be removed from the socket-outlet

before cleaning or maintaining the appliance.

• To avoid injury, keep your ﬁngers and hands away

from the beater bar.

• DO NOT use hot air or hot surface to dry ﬁlters. Keep

at room temperature for approximately 24 hours.

• IMPORTANT: Before re-installing the washable ﬁlters,

make sure they are completely dry to avoid damaging

the cleaner.

Filter care

D-12 Exhaust ﬁlter

Exhaust ﬁlter, is installed in the rear side of the vacuum

cleaner. This ﬁlter retains any small dust particles which

may be present in the expelled air.

lt is advisable to change the clean air ﬁlter once or twice

a year, depending on use. To change the ﬁlter, hold the

exhaust cover (as illustrated). After changed the ﬁlter,

set the exhaust cover to its position (as illustrated).

NOTE:

IMPORTANT: Never use the cleaner without the correct ﬁlters

properly installed. Failure to do so may result in

damage to the motor.

What to do if your cleaner does not work

Check that the appliance is correctly plugged in and that the

electrical socket is working. In case that the thermal cut-out

device has operated, wait until it resets after approximately

60 minutes. If after having checked the mentioned points, the

cleaner does not work, take it to an Authorized Service Centre to

be repaired.

What to do when the suction performance

reduces

• Stop the cleaner and unplug from the socket.

• Check whether the wands, hose and accessories are blocked or

not. If they are blocked, remove the obstruction.

• Check that the dust compartment is full. If it is full, empty it.

• Check that Pre-motor Filter or Exhaust Filter is blocked with

dust. If they are blocked, clean them out or replace.

SPECIFICATIONS

MC-CG467 MC-CG465 MC-CG463

MC-CG461,

MC-CG461A

Power source

230 V~50 Hz

Max. Input 1800 W 1500 W

Nominal input 1500 W 1300 W

Dimensions

(W x L x H)

280 mm x 425 mm x 260 mm

Net weight 4.5 kg

Extension wands

Telescopic

Metal x2/

Telescopic

Crevice nozzle

√ √ √ √

Dusting brush

√ √ √ √

REMINDER FOR CUSTOMER

The model and serial number of this product may be found on the

nameplate located at the underside of your cleaner. You should

note the model and serial number in the spaces provided and

retain this book as a permanent record of your purchase.

Model Number. .............................................................................

Serial No. ......................................................................................

Date Purchased. ...........................................................................

Where Purchased. ........................................................................

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic MC-CG 461 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info