Bedienungsanleitung Panasonic mc cg 467 (Seite 18 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

320123

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS FOR THE USER

Before using the vacuum cleaner, please observe these basic precautions.

WARNING: To reduce the risk of ﬁre, electric shock, or injury

• This appliance is not intended for use by young children or inﬁrm person without supervision; young children should be

supervised to ensure that they do not play with the appliance.

• Do not use the appliance if the mains lead or plug is damaged or faulty.

• This appliance is provided with a mains lead and if this becomes damaged, it must be repaired by an Authorized Service Centre

or a qualiﬁed person in order to avoid any hazard.

• Unplug from the socket when not in use and before cleaning the appliance or undertaking maintenance operations.

• Turn off the appliance before removing the plug. Do not pull on the mains lead, always pull on the plug body itself.

• Do not handle plug or vacuum cleaner with wet hands.

• Do not use wet ﬁlters after wash, make sure they are completely dry to avoid damaging the cleaner.

• Do not vacuum ﬂammable or combustible substances, neither use in areas where they may be present.

• Do not vacuum hot ash, embers or large and sharp objects.

• Do not vacuum water or other liquids.

• Keep the vacuum cleaner away from heat sources such as radiators, ﬁres, direct sunlight, etc.

• This vacuum cleaner is ﬁtted with a thermal cut-out device which automatically turns off the cleaner to prevent overheating of the

motor. When this happens, disconnect the cleaner from the mains socket and check the dust compartment and ﬁlters as they

may be full or clogged with ﬁne dust. Check for any other obstructions in the hose or tube. After removing the obstruction, leave

the cleaner to cool down until the thermal cut-out resets after approximately 60 minutes.

A- IDENTIFICATION OF MAIN PARTS

C - HOW TO OPERATE YOUR CLEANER

B - HOW TO ASSEMBLE YOUR CLEANER

Turbine nozzle (

Only MC-CG467)

Floor nozzle

Connection pipe

Hose

Suction regulator

Curved wand

Telescopic wand

(MC-CG467)

(MC-CG465, MC-CG463)

Extension wand (MC-CG461, MC-CG461A)

I )

Hose inlet

Dust indicator

Dust cover

ON /OFF Switch pedal

Cord rewind pedal

Crevice nozzle

Dusting brush

Parquet ﬂoor nozzle (Only MC-CG465)

Exhaust cover

Plug

Variable power control button

B-1 Insert connection pipe into hose inlet until it locks. When

removing hose assembly, pull out connection pipe with

pushing down two connection buttons.

NOTE: Do not bend, pull and step on the hose or put

anything heavy on it.

B-2 Connect the two extension wands by inserting one into

the other and twisting together. (Only MC-CG461, MC-

CG461A)

B-3 Insert the hose unit into the upper end of the connected

extension wand (MC-CG461, MC-CG461A) or telescopic

wand (MC-CG465, MC-CG463), and the ﬂoor nozzle to

the other end

(MC-CG465, MC-CG463, MC-CG461, MC-CG461A ).

B-4 Insert the hose unit into the upper end of the telescopic

wand. Twist the telescopic wand so that the round hole

will ﬁt into the tab on the hose unit. (When removing the

hose, push the tab down whilst pulling on the telescopic

wand)

Attach the Turbine Nozzle to the other end (Only MC-

CG467)( Removal as per reverse procedure)

B-5 You can adjust the length of telescopic wand by pushing

button. (MC-CG467, MC-CG465, MC-CG463)

C-1 Pull out the mains lead and put the plug into the wall

socket.

C-2 Gently press at the centre of the switch pedal to turn

ON the vacuum cleaner.

Press the pedal again to turn it OFF.

C-3 Power control

To increase or decrease the power, turn the variable

power control button.

C-4 Switching between carpet and ﬂooring

Flooring: Press lever A

Carpet: Press lever B

*Switching 3 positions for MC-CG467.

Flooring (PARQUET): Set position A

Carpet (short): Set position B

Carpet (long or hard to push): Set position C

C-5 The curved wand of the hose is attached with a manual

suction regulator, which allows you to brieﬂy reduce the

suction level.

C-6 After you ﬁnish vacuuming, remove the plug from

the wall socket and press the cord rewind pedal.

When rewinding the power cord, press the cord rewind

pedal by holding the plug so that it does not become

damaged.

C-7 Storage position

Insert the wand holder straight into the wand

supporter.

C-8 Park system

For short breaks during vacuuming, slide the hook

attached to the nozzle pipe into the slot on the rear side

of the cleaner.

NOTE: When you use park position, we suggest the

appliance is switched off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic mc cg 467 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info