136019

Panasonic nv dv 2000 ec Seite 58

58
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
58
Time code
Time Code signals are time data that is recorded on the
tape. The time is expressed in units of hours (h),
minutes (m), seconds (s) and frames (f) (25 frames/
sec). Time codes are recorded concurrently while the
video is being recorded. If a recording is made
continuously from the beginning of a tape, the Time
codes can be used to determine the absolute position of
video and audio recorded on the tape.
When you first record on a new (previously unrecorded)
cassette, the Time codes are also recorded, starting
from zero. If you start recording in the middle of a
cassette that has already been partially recorded, and
you start where the previous recording ended, the Time
code units continue from the ending unit of the previous
recording. However, if you start recording in the middle
of a tape after a blank section of tape, the Time codes
again start from zero.
Unless the Time code is recorded continuously from the
beginning of the tape, precise editing may not be
possible. To ensure that the Time code will be recorded
without interruption, we recommend that you use the
Index Search function before starting to record a new
scene.
Frame
This is a Time code unit. One frame is equivalent to
1/25 of a second. (Refer to the description of Time
codes.)
Tape Counter (Linear counter)
As opposed to the absolute value Time codes (refer to
the explanation of Time codes) that are recorded on
tape simultaneously when video or audio material is
recorded, the tape counter (linear counter) is time
information that can change units. The tape counter is
reset to zero each time a tape is loaded/ejected, and
can also be reset to zero at any other time by pressing
RESET.
3D-DNR (3-Dimensional Digital Noise Reduction)
To activate the 3D DNR function, press the 3D DNR
button, so that the “PB DNR” or “REC DNR” appears on
the VCR display. 3D DNR function will now reduce the
noise during playback or recording.
Use of “REC DNR” during recording reduces the
shaking and distortion that occur during the recording of
analogue tapes so that pictures with a high picture
quality are obtained. Use of “PB DNR” when playing
back pictures from an analogue device reduces the
amount of noise, thereby making it possible to view
pictures with a high picture quality.
≥ During playback, the picture may become the
afterimage. In such a case, cancel the 3D DNR
function.
DV TERMINAL
This terminal is used to input/output video and audio
data on digital video equipment. Because the video and
audio data is sent through the DV cable as digital
signals, there is practically no deterioration in video and
audio quality after copying. In addition, because the
hardware automatically determines the direction of flow
for input and output signals according to the state of the
unit, there is no need to change the connections around
when switching between input and output, as is the case
with conventional AV cables.
In addition, the DV terminal on the NV-DV2000 can also
send control signals that are required in editing
operations. If a Panasonic Digital Video Camera is
used as the playback unit, only one DV cable needs to
be connected between the camera and the NV-DV2000
in order to perform the following editing functions:
Copying, Assemble, Video Insert, and Audio
Insert.
(Such a configuration does not permit AV Insert,
Audio Dubbing, or Audio Mixing. AV cables must
also be connected.)
The following functional differences exist when the
recording unit and the playback unit are connected
through the DV terminal, as opposed to when they are
connected through the audio and video sockets:
≥ The original sub code data (date of the recording,
photoshot index signals, etc.) on the playback unit is
copied as is on the recording unit.
(Time codes are not copied.)
≥ The audio is recorded in the same mode (12bit or
16bit) on the recording unit as it was on the playback
unit. (If you want to change the audio recording
mode, the units must be connected through the audio
and video sockets, not the DV terminal.)
≥ No audio is output while searching with the Jog Dial/
Shuttle Ring.
≥ When playing a tape that was recorded with two audio
channels (main and sub; from a bilingual broadcast,
for example), both the main audio channel and the
sub audio channel are output, regardless of the audio
select (main/sub) setting.
≥ Horizontal sway may appear at the bottom of the
screen for video input from the DV terminal, but this
has no effect on the recording.
… 58 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

panasonic-nv-dv-2000-ec

Suche zurücksetzen

  • DV1 Soket 44 ist doch Fire Wire oder?
    Pinnacle Studio23 erkennt den Player nicht.... Eingereicht am 15-6-2020 17:26

    Antworten Frage melden

  • gibt es die bedienungsanleitung auch in deutscher sprache? Eingereicht am 4-5-2019 17:56

    Antworten Frage melden

  • nach dem einlegen der DV-Kassette schaltet das Gerät aus. Eingereicht am 10-12-2018 18:35

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic nv dv 2000 ec wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info