Bedienungsanleitung Panasonic NVDS60 (Seite 57 von 60) (Englisch)

627357

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ª Memory Stop Function

The Memory Stop Function is useful for the

following operations.

Rewinding or fast-forwarding a tape to a

desired position

1 Set [DISPLAY SETUP] >> [C.DISPLAY]

>> [MEMORY].

2 Reset the Tape Counter to zero at the

tape position from which you want to

play it back later. (l 8, 15)

3 Start playback or recording.

4 After playback or recording has

finished:

Set the [VCR/OFF/CAMERA/M-CARD]

Switch to [VCR].

5 Rewind the tape.

≥The tape automatically stops approximately

at the position where the counter was set to

zero.

Stopping editing automatically during audio

dubbing

1 Set [DISPLAY SETUP] >> [C.DISPLAY]

>> [MEMORY].

2 Reset the Tape Counter to zero at the

position where you want to stop

editing.

3 Play back the still picture where you

want to start audio dubbing.

4 Start audio dubbing. (l 35)

≥Audio dubbing automatically stops at the

position where the counter was set to zero.

ª Owner ID

You can register your name and address in your

Movie Camera to identify the owner.

1 Set [CAMERA FUNCTIONS] >>

[OTHER FUNCTIONS] >>

[OWNER ID SET] >> [ON].

≥The [OWNER ID] Menu appears.

2 Turn the [PUSH] Dial to select

[PIN NUMBER] and press the [PUSH]

Dial to input desired numbers.

3 Turn the [PUSH] Dial to select

numbers and press the [PUSH] Dial to

enter them.

≥You can input 4 digits.

4 Press the [∫] Button.

5 Repeat Steps 2–4 to input desired

characters for [NAME] and

[POSTCODE].

≥You can input up to 12 characters in

[NAME], and up to 11 characters in

[POSTCODE].

6 Press the [∫] Button to finish the

setup.

To verify Owner ID

≥Keep pressing the [;] Button for approximately

5 seconds.

To Check Owner ID

If Owner ID has already been set, carrying out

Step 1 above will display [INPUT PIN NUMBER]

on the screen. Input the Pin Number you have

already selected. If the number is not correct, the

screen will not change. If the number is correct,

the contents of the setup will be displayed. (By

repeating Steps 2 to 4 above, you can change the

contents.)

ª Demonstration Mode

If no operation takes place for approximately

10 minutes after the AC Adaptor was connected to

the Movie Camera and the [VCR/OFF/CAMERA/

M-CARD] Switch was turned to [CAMERA]

without inserting a Cassette, the Movie Camera is

automatically set to Demonstration Mode for

introducing its functions. If any button is pressed

or operated, the Demonstration Mode is

cancelled. The Demonstration Mode can be

started by setting [DEMO MODE] on the

[OTHER FUNCTIONS] Sub-Menu of the

[CAMERA FUNCTIONS] Main-Menu to [ON] and

by exiting the Menu. To terminate the

Demonstration Mode, insert a Cassette or set the

[DEMO MODE] to [OFF].

EG-ENG.book 57 ページ２００３年１月６日　月曜日　午後３時４３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic NVDS60 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic NVDS60

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info