Bedienungsanleitung Panasonic NVMX2B (Seite 55 von 60) (Englisch)

627473

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

≥When attaching the Filter Kit (VW-LF43WE, optional),

attach it on the inside of the lens hood without removing the

lens hood.

≥When you want to attach the Tele Conversion Lens

(VW-LT4314ME; optional) or the Wide Conversion Lens

(VW-LW4307ME; optional), be sure to first remove the lens

Hood by turning it counterclockwise.

≥If you push the [W/T] Lever toward [W] during recording

with the filter or conversion lens attached to the Movie

Camera, 4 corners of the image may become dark

(vignetting). For details, please refer to the operating

instructions of your accessories.

≥Be sure to keep the Lens Hood attached to the Movie

Camera so as to shut out unnecessary light.

~~~~~~~~~~~~~~~~~~~

Before Requesting Repair (Problems

and Solutions)

Power

1: The Movie Camera power cannot be turned on.

1: Is the power source connected correctly?

(

10)

2: The Movie Camera power is turned off

automatically.

2: If you leave the Movie Camera in Recording Pause

Mode for more than 6 minutes, the power is turned off

automatically to protect the tape and to save the Battery

power.

(

18)

3: The Movie Camera power does not stay on long

enough.

3-1: Is the Battery low? Charge the Battery or attach a fully

charged Battery.

(

10)

3-2: Has condensation occurred? Wait until the

Condensation Indication disappears.

(

53)

Battery

1: Battery runs down quickly.

1-1: Is the Battery fully charged? Charge it with the AC

Adaptor.

(

10)

1-2: Are you using the Battery in an extremely cold place? In

cold places, the operating time of the Battery becomes

shorter.

(

54)

1-3: Has the Battery worn out? If the operating time is still

too short even after the Battery is fully charged, the

Battery has worn out.

2: The Battery cannot be charged.

2: If the DC Input Lead is connected to the AC Adaptor,

charging cannot be performed. Disconnect the DC Input

Lead.

Normal Recording

1: Recording does not start although power is

supplied to the Movie Camera and the Cassette is

correctly inserted.

1-1: Is the accidental erasure prevention slider on the

Cassette open? If it is open (set to [SAVE]), recording

cannot be performed.

(

11)

1-2: Is the tape wound to the end? Insert a new Cassette.

(

11)

1-3: Is the Movie Camera power turned on?

(

18)

1-4: Is the [CAMERA] Lamp on? If the [CAMERA] Lamp is

not on, no recording function can be operated.

(

18)

1-5: Has condensation occurred? Wait until the

Condensation Indication disappears.

(

53)

Other Recording

1: Auto Focus Function does not work.

1-1: Is Manual Focus Mode selected? If Auto Focus Mode is

selected, focus is automatically adjusted.

(

23)

1-2: There are some recording subjects and recording

surroundings for which the Auto Focus Function does

not operate correctly. In this case, use the Manual

Focus Mode to adjust the focus.

(

56)

Editing

1: Audio dubbing cannot be performed.

1-1: Is the accidental erasure prevention slider on the

Cassette open? If it is open (set to [SAVE]), recording

cannot be performed.

(

11)

1-2: Are you attempting to edit a tape portion that was

recorded in LP Mode? LP Mode does not allow audio

dubbing to operate.

(

17)

Indications

1: The Time Code becomes inaccurate.

1: The Time Code Indication counter may not be constant

in the reverse direction in Slow Motion Playback Mode,

but this is not a malfunction.

2: The Remaining Tape Time Indication disappears.

2: When you record still pictures in Photoshot Mode, the

Remaining Tape Time Indication may disappear

temporarily. However, it reappears when recording

normally.

3: The Remaining Tape Time Indication does not

match the actual remaining tape time.

3-1: If scenes of less than 15 seconds are continuously

recorded, the remaining tape time cannot be displayed

correctly.

3-2: In some cases, the Remaining Tape Time Indication

may show remaining tape time that is 2 to 3 minutes

shorter than the actual remaining tape time.

Playback (Images)

1: Images cannot be played back even when the

Operation Lever is pushed towards [

1: Is the [VCR] Lamp on? If the [VCR] Lamp is not on, the

playback function cannot be used.

(

27)

2: Mosaic-pattern noise appears on images during

Cue, Review or Slow Motion Playback.

2: This phenomenon is characteristic of digital video

systems. It is not a malfunction.

3: Although the Movie Camera is correctly connected

to a TV, playback images cannot be seen.

3: Have you selected “Video Input” on the TV? Please

read the operating instructions of your TV and select the

channel that matches the input sockets used for the

connection.

4: Playback image is not clear.

4: Are the heads of the Movie Camera dirty? If the heads

are dirty, playback image cannot be clear.

(

53)

Playback (Sound)

1: Sound is not played back from the built-in speaker

of the Movie Camera or the headphones.

1: Is the volume too low? During playback, keep pressing

the [PUSH] Dial until the [VOLUME] Indication appears.

Then, turn the [PUSH] Dial to adjust the volume.

(

27)

2: Different sounds are reproduced at the same time.

2: [12bit AUDIO] on the [PLAYBACK FUNCTIONS]

Sub-Menu of the [VCR FUNCTIONS] Main-Menu has

been set to [MIX]. As a result, the original sound and

sound that was recorded by audio dubbing are played

back together. It is possible to reproduce the sounds

separately.

(

32)

3: The original sound was erased when audio dubbing

was performed.

3: If you perform audio dubbing on a recording done in

[16bit] Mode, the original sound will be erased. If you

wish to preserve the original sound, be sure to select

[12bit] Mode at the time of recording.

Panasonic NVMX2B Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info