215762
24
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
Remote control operation
24 - ENGLISH
Basic Operation
You can monitor if the brightness and
contrast level of the input signal is in the
recommended range by displaying it in the
waveform monitor. See "WAVEFORM
MONITOR" on page 32.
1. Project a commercial adjusting signal.
2. Press the WAVEFORM button to display the
waveform monitor.
3. Press ENTER button to select the required
adjusting mode.
4. Press F G I H to adjust the displaying
position of the waveform monitor.
5. Adjust the waveform in each menu.
J Adjusting the waveform
Make sure to adjust to the 0% line first. Any signal level
below the recommended range will be forced to 0%.
Q Adjusting in PICTURE menu
Press PIC. ADJUST button to display the
PICTURE menu and adjust BRIGHTNESS
(-32 to +32) and CONTRAST (-64 to +64) with
I H.
Q Adjusting in ADVANCED menu
Press PIC. ADJUST twice to display the
ADVANCED menu and adjust BRIGHTNESS
(-16 to +16) and CONTRAST (-32 to +32) in red,
green and blue with I H.
Adjusting the waveform of the input signal
OFF Deactivate the waveform monitor.
FULL SCAN
Monitoring the waveform of
brightness and contrast of the
whole image.
SINGLE LINE
SCAN
Monitoring the waveform of
detailed brightness and contrast in
each horizontal line of the image.
Press F G to select the required
line.
NOTE:
When you adjust the SINGLE LINE SCAN, the
position of the waveform is depends on the
position of the selected line.
When the WAVEFORM displayed, the COLOR
MANAGEMENT is disabled.
FULL SCAN(Y)
SINGLE LINE SCAN(B)
FULL SCAN(R)
SINGLE LINE SCAN(G)
FULL SCAN(G) SINGLE LINE SCAN(R)
FULL SCAN(B) SINGLE LINE SCAN(Y)
BRIGHTNESS
Adjust the bottom line of the
waveform to 0 % (0/7.5 IRE).
CONTRAST
Adjust the top line of the waveform
to 100 % (100 IRE).
In red
BRIGHTNESS R
Adjust the bottom line of the
waveform to 0 % (0/7.5 IRE).
CONTRAST R
Adjust the top line of the waveform
to 100 % (100 IRE).
In green
BRIGHTNESS G
Adjust the bottom line of the
waveform to 0 % (0/7.5 IRE).
CONTRAST G
Adjust the top line of the waveform
to 100 % (100 IRE).
In blue
BRIGHTNESS B
Adjust the bottom line of the
waveform to 0 % (0/7.5 IRE).
CONTRAST B
Adjust the top line of the waveform
to 100 % (100 IRE).
NOTE:
When the Main menu (except WAVEFORM and
individually displayed menu item) is displayed, the
waveform monitor will be halt.
When the waveform monitor is displayed, the
Main menu will be displayed in order not to
interfere the waveform monitor.
100%
50%
0%
100%
5
0
%
0%
100%
5
0
%
0%
ENTER
Optimal
dynamic range
Adjust to 100%
Adjust to 0%
Monitor position
Optimal
dynamic range
Adjust to 100%
Adjust to 0%
Monitor position
PC/HDMI (Expand)
Signal level
Signal level
PT-AE1000U.book Page 24 Monday, October 16, 2006 1:40 PM
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic pt ae1000e wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info