215762
43
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
Care and Replacement
ENGLISH - 43
Maintenance
J Removing and replacing the lamp unit
1. Use a Phillips screw driver to loosen the 3 lamp unit fixing
screws until the screws turn freely.
2. Hold the handle of the lamp unit and release the lamp unit
lock.
3. Pull out the lamp unit gently from the projector.
4. Replace the new lamp unit while making sure that the
direction of insertion is correct.
Press the top of the lamp unit and make sure the unit is
installed securely.
5. Tighten the lamp unit fixing screws securely with a Phillips
screwdriver.
J Attaching the top cover
1. Attach the hinge parts of the top cover to the projector and press slightly
until it clicks.
2. Hook the tabs of the top cover to the projector and lift down slowly.
3. Press the back corner of the top cover gently until it clicks.
J Resetting the LAMP RUNTIME
If the lamp usage time has passed 2 000 hours (when LAMP POWER has been set to NORMAL), the projector will
switch to standby mode after approximately 10 minutes of operation. The resetting procedure should thus be
completed within 10 minutes. See “LAMP RUNTIME” on page 39.
1. Connect the Power cord to the projector and a
wall socket, and switch the MAIN POWER on.
2. Switch the POWER button.
3. Press the MENU button to display the menu.
4. Press F G to select OPTION and press ENTER.
5. Press F G to select LAMP RUNTIME.
6. Press and hold the ENTER button for
approximately 3 seconds.
7. The confirmation screen will be displayed and
select OK.
8. Switch off the POWER to reset the duration of the
LAMP RUNTIME.
9. Confirm the duration of time in LAMP RUNTIME is
reset to “0”.
Lamp unit
fixing screws
Lamp unit lock
Press here Press here
NOTE:
Be sure to install the lamp unit and the top cover of the projector securely. If they
are not securely installed, it may cause the protection circuit to operate so that the
power cannot be turned on.
Grip the handle and keep the lamp unit paralleled when you remove the Lamp unit.
Some parts of the lamp unit are sharpened and may cause injury.
Do not switch the power on while the top cover is opened.
When the projector is mounted in the ceiling, keep the lamp unit paralleled and
remove.
S
LEEP
OFF
LOW
NORMAL
1820H
FUNCTION BUTTON
LAMP POWER
ALTITUDE
LAMP RUNTIME
PT-AE1000U.book Page 43 Monday, October 16, 2006 1:40 PM
43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic pt ae1000e wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info