216305
14
Zoom out
Zoom in
Vorherige Seite
1/50
Nächste Seite
Remote control operation
14 -
E
NGLISH
Loading a saved setting
You can access saved settings instantly. See
“MEMORY LOAD” on page 31.
Select the required setting from 1. MEMORY 1 - 16.
Undened setting will not be displayed.
Press the 2. ENTER button to activate the selected
setting.
NOTE:
If you have not saved any settings, MEMORY 1 - 16
will not be displayed.
VIERA Link
You can control some functions of the connected equipment with this projector remote control.
See the operating instructions for more details.
Adjusting the signal condition with a waveform
You can display the image brightness and
contrast level of the input signal with a
waveform. See “WAVEFORM MONITOR” on
page 21.
FULL SCAN
Monitoring the waveform of
brightness and contrast of the whole
image.
SINGLE LINE SCAN
Monitoring the waveform of
brightness and contrast in each
horizontal line of the image.
Displaying the waveform
J
Press the 1. WAVEFORM MONITOR button and
display the waveform monitor.
Press the
WAVEFORM MONITOR button again to
escape from the waveform mode.
Press the 2. ENTER button until the required
waveform option is displayed.
In
FULL SCAN mode, press ▲ ▼ ◄ ► to change
the waveform position.
In
SINGLE LINE SCAN mode, press ▲ ▼ to select
the required line position.
FULL SCAN(Y) SINGLE LINE SCAN(B)
FULL SCAN(R) SINGLE LINE SCAN(G)
FULL SCAN(G) SINGLE LINE SCAN(R)
FULL SCAN(B) SINGLE LINE SCAN(Y)
NOTE:
In SINGLE LINE SCAN mode, the position of the waveform monitor depends on the position of the selected line.
You can display the main menu by pressing the MENU button and adjust the menu items.
The called up menu items displayed position depends on the position of the waveform monitor.
You can activate AUTO ADJUST of the WAVEFORM MONITOR menu by pressing the DEFAULT button.
The signal which is lower than 0 % in the waveform will be displayed as same as 0 % on the projected image.
While the waveform is displayed, you can not adjust the COLOUR MANAGEMENT settings.
Capturing an image
Press the FREEZE button to capture the
image, and you can see it as a still picture
while the AV equipment are still running. Press
the FREEZE button again to escape and return
to the continuing image.
While displaying the frozen image, you can enter the
AREA SELECT mode of the SPLIT ADJUST menu by
pressing the ENTER button. See “SPLIT ADJUST” on
page 22.
Resetting to the factory default settings
You can reset most of the customised
settings to the factory defaults by pressing
the DEFAULT button. Display the required
sub-menu or the menu items and press the
button.
NOTE:
Some menu items are not available to reset by
pressing the DEFAULT button. Adjust each menu item
manually.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic pt ae4000e wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Panasonic pt ae4000e

Panasonic pt ae4000e Bedienungsanleitung - Deutsch - 50 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info