Bedienungsanleitung Panasonic PT-AE7000EA (Seite 33 von 104) (Englisch)

543815

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Remote control operation

ENGLISH

- 33

Basic Operation

Loading a saved setting

Displays the [MEMORY LOAD] menu.

Press

Attention

Setting can also be performed using the on-screen menu.

For details, see [MEMORY LOAD] in the [PICTURE]

menu. (



page 56)

Displaying the [VIERA LINK

MENU] menu

You can control some functions of the external device

with this projector remote control.

Press

Note

See “Using VIERA Link” for details. (



page 91)

Displaying the waveform

monitor

By displaying the output signal from a connected

external device with a waveform, you can check if the

video signal (luminance) level is set to a value within

this projector’s recommended range, and can adjust it

accordingly.

Press

The settings change as follows each time the

<ENTER> button is pressed.

[FULL SCAN (Y)] [FULL SCAN (R)]

[SINGLE LINE SCAN (B)] [FULL SCAN (G)]

[SINGLE LINE SCAN (G)] [FULL SCAN (B)]

[SINGLE LINE SCAN (R)] [SINGLE LINE SCAN (Y)]

The waveform monitor disappears when the

<WAVEFORM MONITOR> button is pressed again.

Note

Setting can also be performed using the on-screen menu.

For details, see [WAVEFORM MONITOR] in [PICTURE]

menu. (



page 41)

[FULL

SCAN]

Checks that the waveform for each of the

Y- (brightness), R- (red), G- (green), and

B- (blue) values for the whole image is

within the recommended range.

[SINGLE

LINE

SCAN]

Checks that the waveform for each of the

Y- (brightness), R- (red), G- (green), and

B- (blue) values for an arbitrary number

of lines from the top of the screen to the

bottom is within the recommended range.

Enables more detailed conrmation than

[FULL SCAN].

Line position can be changed with the ▲▼

buttons

The display position of the [WAVEFORM

MONITOR] changes depending on the line

position.

Note

Signals lower than 0 % in the waveform monitor will be

displayed as same as 0 % on the projected image.

[SINGLE LINE SCAN] can display horizontal lines in Y-

(brightness), R- (red), G- (green), and B- (blue) from the

top of the screen to the bottom more nely than [FULL

SCAN], and each item can be adjusted in the same way

as [FULL SCAN].

When selecting [FULL SCAN], the display position of the

waveform can be set using the ▲▼

▲

▼

buttons.

So that the display of individual adjustment screen in

[PICTURE] does not interfere with the waveform monitor,

the positioning of this screen differs depending on the

circumstances at the time.

The [AUTO ADJUST] is executed by pressing the

<DEFAULT> button while the waveform is displayed.

(



page 42)

While the waveform monitor is displayed, you cannot

adjust the [COLOUR MANAGEMENT] settings.

When a 3D signal is being input (including converting 2D

to 3D), the waveform monitor cannot be displayed.

If a 3D signal is input while the waveform monitor is being

displayed, the waveform monitor disappears.

Resetting to the default

settings

You can reset most of the settings or adjustment

values for submenus to factory default settings.

Press

For details, see “Navigating through the menu -

Returning adjusted values to default settings” of “Menu

navigation”. (



page

37)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-AE7000EA Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-AE7000EA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info