Bedienungsanleitung Panasonic PT-AE7000EA (Seite 76 von 104) (Englisch)

543815

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

[OPTION] menu

76 -

ENGLISH

Settings

[BLANK]•

When [BLANK] is activated, output is 12 V. If the

setting is released, output is 0 V.

[RS-232C COMMAND LINK]•

Receives commands (



page 98) from external

device and outputs 12 V.

Input

[POWER ON/OFF] [BLANK]

[POWER ON/OFF]•

If the trigger input signal from the external device is

changed from 0 V to 12 V, the projector power will be

switched on. And if it is changed from 12 V to 0 V, the

power will be switched off.

[BLANK]•

If the trigger input signal from the external device is

changed from 0 V to 12 V, the screen will go blank. And

if it is changed from 12 V to 0 V, the [BLANK] setting

will be released.

Press the ▲▼◄► buttons to move the 3)

cursor to [DELAY TIME]

Press the ◄► buttons to set the delay 4)

time for the trigger output signal

The delay time can be set to 2, 4, 6, 8, 10, 20, and

30 seconds.

It is possible to delay the trigger output signal (12 V)

by the amount of time set. (Only available if trigger

output item is selected.)

E.g.) Select [SELECT 4:3 ASPECT] of the trigger output

function and set the delay time to 10 seconds.

Set the [ASPECT] in the [POSITION] menu to [4:3],

and 12V is output from the trigger port after 10

seconds.

Note

You should not use trigger terminal output as the power

source for other devices.

The projector will not accept trigger input while preparing

to project after the power has been switched on and

while preparing to shutdown after projection. Input trigger

signals after projection starts or after entering standby

mode.

12 V cannot be output from the trigger terminal when the

projector is in standby mode.

[SLEEP]

Set the time for the power to be automatically turned

off.

Switch settings Switch settings

[OFF] Inactive

[60MIN.] Turn power off after 60 minutes

[90MIN.] Turn power off after 90 minutes

[120MIN.] Turn power off after 120 minutes

[150MIN.] Turn power off after 150 minutes

[180MIN.] Turn power off after 180 minutes

[210MIN.] Turn power off after 210 minutes

[240MIN.] Turn power off after 240 minutes

Note

The projector automatically enters power off preparation

mode (the power indicator illuminates orange), and then

enters standby mode (the power indicator illuminates or

ashes in red). (



page 28)

3 minutes before turn-off, the number of minutes

remaining will be displayed in the lower right corner.

If [SLEEP] mode is set to [OFF] mode before the

specied time has elapsed the settings are erased.

[HIGH ALTITUDE MODE]

Set to [ON] when using at locations between 1 400 m

and 2 700 m above sea level.

Switch settings Switch settings

[OFF]

When using at an altitude of less

than 1 400 m above sea level

[ON]

When using at high altitudes

(between 1 400 m and 2 700 m

above sea level)

Note

The fan rotation and operating noise increases if set to

[ON].

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-AE7000EA Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-AE7000EA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info