Bedienungsanleitung Panasonic PT-CW230EA (Seite 58 von 81) (Englisch)

542439

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

- ENGLISH

Settings

PIN code change

The PIN code can be changed to your desired four-

digit number.

Press ▲▼ to select [PIN code change] 1 )

and then Press <SELECT> button.

Current Pin code dialog box appears.

Press ▲▼ to enter the current code. 2 )

Press ► button to x the number and

move the red frame pointer to the next

box.

The New PIN code input dialog box appears.

Repeat these steps to set a new PIN 3 )

code.

Attention

Be sure to note the new PIN code and keep it on hand. If

you lost the number, you could no longer change the PIN

code setting.

Fan

Press ▲▼ to select [Fan] and then 1 )

press <SELECT> button.

Press ▲▼ to select one option.2 )

This function provides the following options in

the cooling fans’ operation when the projector is

turned off.

L 1

It takes less time to cool the

projector down than L 2 mode.

L 2

Slower and lower-sound than

L 1 mode, but it takes more time

to cool the projector down.

Fan control

Press ▲▼ to select [Fan control] and 1 )

then Press <SELECT> button.

Press ▲▼ to select one among 2 )

options as below.

Choose the running speed of cooling fans from

the following options according to the ground

elevation under which you use the projector.

Off

Normal speed.*

On 1

Faster than [Off] mode.*

On 2

Faster than [On 1] mode.*

Set this function to [Off] when using the projector *1 :

in non-high altitude environment.

Select this mode when using the projector in high *2 :

altitudes (about 1 000 meters or more above

the sea level) where the fans have less cooling

effect.

Select this mode when using the projector in *3 :

higher altitudes (than above where the fans have

lesser cooling effect).

It is recommended to select [On 1] when the altitudes

is over about 1 000 m and select [On 2] when the

altitudes is over about 2 000 m.

Note

Failure to set the running speed of cooling fans

properly may affect the projector life.

The fan noise becomes louder in [On 1] and [On 2].

Lamp runtime

This function is used to display the cumulative lamp

operating time and reset the lamp runtime.

Press ▲▼ to select [Lamp runtime].1 )

Press ►or the <SELECT> button to 2 )

access the submenu items.

Lamp runtime

Show the total accumulated lamp run time.

Lamp runtime reset

After replacing the lamp unit, be sure to reset the

timer.

Press ▲▼ to select [Lamp runtime 1 )

reset].

Press the <SELECT> button. 2 )

[Lamp runtime Reset?] appears. Select [Yes]

to continue. Another conrmation dialog box

appears, select [Yes] to reset the Lamp runtime.

Attention

When the lamp run time is elapsed the estimated

duration, [Lamp runtime] will be displayed in red

and the Lamp replacement icon (

page 64) will

appear on the screen, indicating that the end of

lamp life is reached. When replacing the lamp unit,

reset the lamp runtime.

Setting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-CW230EA Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info