511572
19
Zoom out
Zoom in
Vorherige Seite
1/74
Nächste Seite
Using Remote control
ENGLISH -
19
Preparation
Installing and Removing battery
Press the guide and pull 1 )
out the battery base.
3
V
O
L
T
S
CR2025
M
3
V
O
L
T
S
CR2025
Install new battery into 2 )
the compartment.
3
V
O
L
T
S
CR2025
M
3
V
O
L
T
S
CR2025
Remove the old
Lithium coin cell
battery and install
new one (CR2025).
Ensure that the side
with a “+” is facing
up.
Put the cover back.3 )
3
V
O
L
T
S
CR2025
M
3
V
O
L
T
S
CR2025
Attention
When discarding a lithium coin battery, be sure both sides (+/-) are covered with adhesive insulating tape, such as and the
z
cellophane tape, and discard it according to the instructions of the local government.
Setting Remote control ID numbers
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each
projector individually using single remote control, if unique ID number is assigned to each projector.
After setting the remote control ID of the projector, set the same remote control ID to the remote control.
There are 7 different remote control IDs: [All], [ID1]~[ID6], the initial remote control ID is [All].
Setting the remote control ID
J
1) While holding down the <MENU> key, press the <IMAGE> key. The number of times you press the
<IMAGE> key corresponds to the desired remote control ID.
The number of times to press the <IMAGE> key is as follows:
ID1 = Once, ID2 = Twice, ID3 = 3 times, ID4 = 4 times, ID5 = 5 times, ID6 = 6 times.
2) The remote control ID is changed when the <MENU> button is released.
J
Resetting the remote control ID
1) The remote control ID is reset to [All] (default) by pressing the <MENU> key and <IMAGE> key at the
same time for 10 seconds or more.
Note
When operating the projector under [All] code, you can operate several projectors at the same time.
z
If the <IMAGE> button is pressed 7 times or more, the remote control ID cannot be changed (the operation is invalid).
z
For setting the remote control ID codes, see [Remote ID] in the [Setting] menu. (
z
Æ
page 41)
If the battery is not in use for a long period of time and is removed from the remote control, the remote control ID will be
z
reset.
Using Remote control
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic PT-CW330E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info