Bedienungsanleitung Panasonic PT-D6000E (Seite 19 von 42) (Englisch)

502445

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

ENGLISH - 19

Basic Operation

Projecting

 Switching on the projector

When using an optional lens, install a projection lens

before switch on the projector.

1. Connect the supplied mains lead (220 - 240 V AC,

50 Hz/60 Hz) to the AC IN terminal.

2. Remove the projection lens cover from the lens.

3. Switch the POWER switch on that is on the side of the

projector.

 The power indicator lamp on the projector will flash in red.

After a short period, the indicator will illuminate and the

projector will enter standby mode.

4. Press the POWER ON button

 The power indicator lamp illuminates in green and soon the

image is projected on the screen.

 Making adjustment and selection

It is recommended that the projector be allowed to warm

up for at least 30 minutes before any adjustments are

made to the focus.

1. Roughly adjust the focus of the lens.

2. Select and set the projection scheme of

INSTALLATION and COOLING CONDITION settings in

PROJECTOR SETUP menu.

3. Select the input signal by pressing the INPUT SELECT

buttons.

4. Adjust the vertical tilt of the projector with the front leg

adjusters.

5. Adjust the shift position of the projection.

 If the input signal is RGB signal, additionally press the

AUTO SETUP button to adjust the position of the image.

6. Zoom the lens so the image fills the screen.

7. Readjust the focus.

8. Readjust the zoom so that the image size fits in the

screen.

 Adjusting focus, zoom and shift

Projecting a image

NOTE:

• If the projector is powered up at about 0 °C (32 °F), a warm-

up period of approximately 5 minutes may be necessary to

start projection. The temperature monitor (TEMP) lamp lights

up during the warm-up period. When the warm-up is

completed, the temperature monitor (TEMP) lamp turns off

and the image is projected on the screen.

• If the temperature of the operating environment is low and

warm-up takes more than 5 minutes, the projector will judge

that a problem has occurred and the power will be turned off

automatically. If this happens, increase the temperature

around the projector so that it is

0 °C (32 °F) or higher, and

then turn on the POWER switch and press the POWER ON

button again.

POWER switch

AC IN terminal

POWER ON button

Control buttons of the

projector

Pressing the LENS button changes the

setup screen in order of FOCUS, ZOOM

and SHIFT. Press F G I H to adjust.

Remote control buttons

Press FOCUS, ZOOM or SHIFT button

to display the setup screen. Press F G

I H to adjust.

CAUTION:

• Be careful not to catch your fingers between the lens and

shroud when shifting the lens.

NOTE:

• The setup screen will be displayed with the optional fixed lens

though, it will not be functioning.

• Pressing F G I or H for 3 seconds or more, performance

the adjustment faster.

LENS button

INPUT SELECT buttons

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-D6000E Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-D6000E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info