Bedienungsanleitung Panasonic PT-DS20K2 (Seite 22 von 223) (Englisch)

598881

Zoom out

Zoom in

Vorherige Seite

1/223

Nächste Seite

Chapter 1 Preparation — Precautions for use

22 - ENGLISH

Cautions on use

rTo get a good picture quality

In order to view a beautiful image in higher contrast, prepare an appropriate environment. Draw curtains or blinds

over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from

shining onto the screen.

rDo not touch the surface of the projection lens with your bare hands.

If the surface of the projection lens becomes dirty from ngerprints or anything else, this will be magnied and

projected onto the screen.

Attach the supplied lens cover to the optional projection lens when not using the projector.

rDLP chips

f The DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or always

lit. Such a phenomenon does not indicate malfunction.

f Directing a high-power laser beam onto the projection lens surface can damage the DLP chips.

rDo not move the projector or subject it to vibration or impact while it is operating.

Doing so may shorten the life of the built-in motor.

rLamp

The light source of the projector is a high-pressure mercury lamp.

A high-pressure mercury lamp has the following characteristics.

f The luminance of the lamp will decrease by duration of usage.

f The lamp may burst with a loud sound or have its service life shortened because of shock, chipping, or

degradation due to cumulative runtime.

f The lamp life varies greatly depending on individual differences and usage conditions. In particular, frequent on/

off switching of the power greatly deteriorate the lamp and affects the lamp life.

f Continuous use for over one week will deteriorate the lamp. The degradation of the lamp due to continuous use

can be reduced by using the [PROJECTOR SETUP] menu → [LAMP RELAY].

f In rare cases, the lamps burst shortly after projection starts.

f The risk of bursting increases when the lamp is used beyond its replacement cycle. Make sure to replace the

lamp unit regularly.

(“When to replace the lamp unit” (x page 184), “How to replace the lamp unit” (x page 184))

f If the lamp bursts, gas contained inside of the lamp is released in the form of smoke.

f It is recommended that you store the replacement lamp unit as a contingency.

rComputer and external device connections

f When connecting a computer or an external device, read this manual carefully regarding the use of power cords

and shielded cables as well.

rViewing 3D images

(Only for PT-DZ21K2, PT-DS20K2)

The projector can display the 3D video signal input in various formats such as “frame packing”, “side by side”, etc.

You are required to prepare external devices for viewing 3D images (such as 3D eyewear, video signal output

devices) which are suitable for your 3D system. Connections of the projector and external devices vary depends

on the 3D system to be used, see the operating instructions of external devices you use.

Refer to “List of 3D compatible signals” (x page 212) for the types of 3D video signals that can be used with the

projector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DS20K2 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-DS20K2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info