598890
100
Zoom out
Zoom in
Vorherige Seite
1/129
Nächste Seite
NETWORK menu
100
- ENGLISH
Settings
Error information page
J
When “Error (Detail)” is displayed on the status information screen, click it to display the error details.
Depending on the nature of the error, the projector may be placed in the standby mode for its own
z
protection.
When [FAILED] has appeared for an item
Q
Parameter Description
MAIN CPU BUS Trouble has occurred in the microcomputer circuitry. Consult your dealer.
FAN Trouble has occurred in the fan or its drive circuit. Consult your dealer.
INPUT AIR TEMPERATURE
The input air temperature is too high. It may be that the projector is being used in an
operating environment where the temperature is high such as near a heating appliance.
OPTICS MODULE TEMPERATURE
The temperature inside the projector is high. It may be that the projector is being used
in an operating environment where the temperature is high such as near a heating
appliance.
AROUND LAMP TEMPERATURE
The temperature around the lamp is too high. It may be that the projector’s ventilation
holes are blocked.
LAMP1 REMAIN TIME
The lamp runtime has exceeded the prescribed cumulative time, and it is now time to
replace the lamp.
LAMP2 REMAIN TIME
LAMP1 STATUS
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
LAMP2 STATUS
APERTURE (CONTRAST-SHUTTER) Trouble has occurred in the contrast shutter circuitry. Consult your dealer.
INPUT AIR TEMP. SENSOR
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
OPTICS MODULE TEMP. SENSOR
Trouble has occurred in the temperature detection sensor inside the projector.
Consult your dealer.
AROUND LAMP TEMP. SENSOR
Trouble has occurred in the sensor used to detect the exhaust air temperature.
Consult your dealer.
BATTERY The backup battery has been run out. Consult your dealer.
AIRFLOW SENSOR
Trouble has occurred in the sensor used to detect the airow volume.
Consult your dealer.
COVER OPEN The lamp unit cover is not attached securely. Check the lamp unit compartment.
ACF UNIT The air cleaning lter (ACF) is not installed or trouble has occurred. (
Æ
109 page)
FILTER REMAIN The lter remaining is getting less. (
Æ
108 page)
BRIGHTNESS SENSOR
Trouble has occurred in the brightness sensor. If the problem cannot be corrected by
turning the power off and on, consult your dealer.
AC POWER
AC power supply voltage input has dropped. Check that there is sufcient
electrical wiring capacity for the projector’s power consumption requirements.
Note
The ACCESS ERROR INFORMATLION/ACCESS INFORMATION displays the past several thousand accesses/requests.
z
If many accesses/requests are made at a time, some of them may not be found in the information.
Check the ACCESS ERROR INFORMATION/ACCESS INFORMATION regularly.
z
OK: Normal operation
FAILED: Occurrence of trouble
100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic PT-DS8500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info