Bedienungsanleitung Panasonic PT-DW830E (Seite 25 von 190) (Englisch)

543731

Zoom out

Zoom in

Vorherige Seite

1/190

Nächste Seite

Chapter 1 Preparation — About your projector

ENGLISH - 25

About your projector

Remote control

Front Top

Bottom

1 Power standby <v> button

Sets the projector to the state where the projector is switched

off (standby mode) when the <MAIN POWER> switch on the

projector is set to <ON> and in projection mode.

2 Power on <b> button

Starts projection when the <MAIN POWER> switch on the

projector is set to <ON> when the power is switched off

(standby mode).

3 Remote control indicator

Flashes if any button in the remote control is pressed.

4 Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons

Adjusts the projection lens. (x page 58)

5 <MENU> button/<ENTER> button/asqw buttons

Used to navigate through the menu screen. (x page 65)

6 <ON SCREEN> button

Switches on (display)/off (hide) the on-screen display function.

(x page 61)

7 Input selection (<RGB1/2>, <DIGITAL LINK>, <DVI-D>,

<VIDEO>, <SDI>, <HDMI>) buttons

Switches the input signal to project. (x page 62)

8 <FUNCTION> button

Assigns a frequently used operation as a shortcut button.

(x page 63)

9 Number (<0> - <9>) buttons

Used when the system uses multiple projectors.

Used to input ID numbers or passwords.

10 <AUTO SETUP> button

Automatically adjusts the image display position while projecting

the image.

[PROGRESS] is displayed on the screen while adjusting

automatically. (x page 63)

11 <SHUTTER> button

Used when temporarily turning off the image. (x page 61)

12 <TEST PATTERN> button

Displays the test pattern. (x page 63)

13 <STATUS> button

Displays the projector information.

14 <DEFAULT> button

Resets the content of the sub-menu to the factory default.

(x page 66)

15 <ID SET> button

Sets the ID number of the remote control to use for a system

using multiple projectors. (x page 29)

16 Remote control signal transmitter

17 Remote control wired terminal

Connects to the projector with a cable. (x page 30)

Attention

f Do not drop the remote control.

f Avoid contact with liquids or moisture.

f Do not attempt to modify or disassemble the remote control.

Note

f When operating the remote control by directly pointing the receiver of the projector, operate the remote control at a distance approx. 30 m

(98'5") or shorter from the remote control receiving section. The remote control can control at angles of up to ±30° vertically and horizontally,

but the effective control range may be reduced.

f If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.

f The signal will be reected off the screen. However, the operating range may be limited from light reection loss due to the screen material.

f If the remote control signal receiver directly receives strong light, such as uorescent light, the remote control may not operate properly. Use

it in a place distant from the light source.

f The power indicator <ON (G)/STANDBY (R)> will ash if the projector receives a remote control signal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DW830E Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-DW830E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info