Bedienungsanleitung Panasonic PT-DW830E (Seite 158 von 190) (Englisch)

543731

158

Zoom out

Zoom in

Vorherige Seite

1/190

Nächste Seite

Chapter 5 Maintenance — Lamp/temperature/lter indicators

158 - ENGLISH

Temperature indicator <TEMP>

Indicator status Lighting in red

Flashing in red

(2 times)

Flashing in red

(3 times)

Status Warm-up status

Internal temperature is high

(warning).

Internal temperature is high

(standby status).

The cooling fan has

stopped.

Cause

f Did you turn on the power

when the temperature

was low (around 0 °C

(32 °F))?

f Is the air intake/exhaust port blocked?

f Is the room temperature high?

f Is the lter indicator <FILTER> lit?

―

Solution

f Wait at least ve minutes

in the current status.

f Install the projector in a

location with the operating

environment temperature

between 0 °C (32 °F) and

45 °C (113 °F)

f Remove any objects that are blocking the air intake/

exhaust port.

f Install the projector in a location with the operating

environment temperature between 0 °C (32 °F) and

45 °C (113 °F)

f Do not use the projector at high altitudes of 2 700 m

(8 858') or higher above sea level.

f Clean or replace the air lter. (x page 159)

f Turn the <MAIN POWER>

switch to <OFF>

(x page 57), and

consult your dealer.

*1 When using the projector at high altitudes (1 400 m (4 593') or higher – lower than 2 700 m (8 858') above sea level), the operating environment

temperature should be between 0 °C (32 °F) and 40 °C (104 °F).

Note

f If the temperature indicator <TEMP> is still lit or ashing after taking the preceding measures, ask your dealer for repair.

f If you use the projector with the following two settings, the light output may drop by approx. 20 % to protect the projector when the operating

environment temperature becomes 40 °C (104 °F) or higher (35 °C (95 °F) or higher when [HIGH ALTITUDE MODE] is set to [ON]).

g When [LAMP SELECT] is set to [DUAL] from the menu

g When [LAMP POWER] is set to [NORMAL] from the menu

Filter indicator <FILTER>

Indicator status Lighting in red Flashing in red

Status

The lter is clogged.

The temperature inside or outside the projector is abnormally high.

The air lter case is not

attached.

Cause f Is the air lter dirty?

f Is the air intake/exhaust

port blocked?

f Is [HIGH ALTITUDE

MODE] set correctly?

f Is the air lter case

attached?

Solution

f Clean or replace the air

lter. (x page 159)

f Remove any objects that

are blocking the air intake/

exhaust port.

f When using the projector

at high altitudes between

1 400 m (4 593') or higher

and lower than 2 700 m

(8 858') above sea level,

set [HIGH ALTITUDE

MODE] (x page 109) to

[ON].

f Do not use the projector

at high altitudes of

2 700 m (8 858') or higher

above sea level.

f Attach the air lter case.

Note

f If the lter indicator <FILTER> is still lit or ashing after taking the preceding measures, ask your dealer for repair.

f If the air lter case is not attached when the projector is switched on, the lter indicator <FILTER> ashes in red, and then the projector is

switched off after ten minutes.

f If the lter is clogged, only one lamp may light even when [LAMP SELECT] is set to [DUAL]. The status can be reset when the air lter is

cleaned or replaced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DW830E Seite 158

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-DW830E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info