Bedienungsanleitung Panasonic PT-DW830EK (Seite 63 von 190) (Englisch)

544151

Zoom out

Zoom in

Vorherige Seite

1/190

Nächste Seite

Chapter 3 Basic Operations — Operating with the remote control

ENGLISH - 63

Using the automatic setup function

The automatic setup function can be used to automatically adjust the resolution, clock phase, and image position when analog RGB signals

consisting of bitmap images such as computer signals are being input, or to automatically adjust the image position when DVI-D/HDMI signals

are input. Supplying images with bright white borders at the edges and high-contrast black and white characters is recommended when the

system is in automatic adjustment mode.

Avoid supplying images that include halftones or gradation, such as photographs and computer graphics.

button

1) Press the <AUTO SETUP> button.

f [COMPLETE] is displayed when it has completed without any problem.

f This operation can be also performed using the <AUTO SETUP> button on the control panel.

Note

f The clock phase may shift even if it has completed without any incident. In such cases, adjust the [POSITION] menu → [CLOCK PHASE]

(x page 80).

f If an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or adjustment may not be performed properly even

when [COMPLETE] appears. In this case, adjust the settings in the [ADVANCED MENU] menu → [INPUT RESOLUTION] (x page 85),

[POSITION] → [CLOCK PHASE] (x page 80), and [SHIFT] (x page 78).

f Adjust special signals according to the [DISPLAY OPTION] menu → [AUTO SETUP] (x page 97).

f Automatic adjustment may not work depending on the model of the computer.

f Automatic adjustment may not work for a synchronization signal of C-SY or SYNC ON GREEN.

f Images may be disrupted for a few seconds during automatic adjustment, but it is not a malfunction.

f Adjustment is required for each input signal.

f Automatic adjustment can be canceled by pressing the <MENU> button during the automatic adjustment operation.

f If the automatic setup function is used while moving images are being input, the adjustment may not be performed properly even for an RGB

signal that can use automatic setup. [INCOMPLETE] may appear, or adjustment may not be nished properly even if [COMPLETE] appears.

Using the function button

[P IN P], [SUB MEMORY], [SYSTEM SELECTOR], [SYSTEM DAYLIGHT VIEW], [FREEZE], [WAVEFORM MONITOR], [LEFT/RIGHT SWAP],

or [ASPECT] operations can be assigned to the <FUNCTION> button on the remote control so that it can be used as an easy shortcut button.

button

1) Press the <FUNCTION> button.

Note

f Assignment of the function is performed from the [PROJECTOR SETUP] menu → [FUNCTION BUTTON] (x page 121).

Displaying the internal test pattern

The projector has eight types of internal test patterns to check the condition of the set. To display test patterns, perform the following steps.

button

1) Press the <TEST PATTERN> button.

2) Press qw to select the test pattern.

Note

f Setting is also available from the [TEST PATTERN] (x page 126) menu.

f Settings of position, size, and other factors will not be reected in test patterns. Make sure to display the input signal before performing

various adjustments.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DW830EK Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info