Bedienungsanleitung Panasonic PT-DX610EL (Seite 122 von 132) (Englisch)

543726

122

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

122 - ENGLISH

Chapter 6 Appendix — Technical information

Sync. method Asynchronous

Baud rate 9 600 bps

Parity None

Character length 8 bit

Stop bit 1 bit

X parameter None

S parameter None

Basic format

Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according

to the details of control.

E\WHV

,'FKDUDFWHUV

E\WHV

6HPLFRORQ

E\WH

&RORQE\WH

&RPPDQG

FKDUDFWHUVE\WHV

3DUDPHWHU

XQGHILQHGOHQJWK

(QGE\WH

6WDUWE\WH

==±DQG$±=

,'VHWWLQJDUHD

Attention

If a command is transmitted after the lamp starts illuminating, there may be a delay in response or the command may not be executed. Try

sending or receiving any command after 60 seconds.

When transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the response from the projector before

sending the next command. When transmitting a command which does not need a parameter, a colon (:) is not necessary.

Note

If a command cannot be executed, an “ER401” response is sent from the projector to the computer.

If an invalid parameter is sent, an “ER402” response is sent from the projector to the computer.

ID transmission in RS-232C supports ZZ (ALL) and 01 to 64, as well as 0A to 0Z groups.

If a command is sent with a specied ID, a response will be sent to the computer only in the following cases.

It matches the projector ID

ID setting is set to ALL and [RESPONSE(ID ALL)] is [ON]

ID setting is set to GROUP and [RESPONSE(ID GROUP)] is [ON]

STX and ETX are character codes. STX shown in hexadecimal is 02, and ETX shown in hexadecimal is 03.

When multiple projectors are controlled

When multiple projectors are all controlled

When controlling multiple projectors together via RS-232C, perform the following settings.

Set a different ID for each projector.

Set [RESPONSE(ID ALL)] to [ON] in only one

projector.

Set [RESPONSE(ID ALL)] to [OFF] for all other

projectors set in Step 2).

When multiple projectors are all controlled by group unit

When controlling multiple projectors by group unit via RS-232C, perform the following settings.

Set a different ID for each projector.

Set [RESPONSE(ID GROUP)] to [ON] in only

one projector.

Set [RESPONSE(ID GROUP)] to [OFF] for all

other projectors set in Step 2).

Note

There will be no response if 2 or more projectors have [RESPONSE(ID ALL)] set to [ON].

There will be no response if 2 or more projectors of the same group have [RESPONSE(ID GROUP)] set to [ON].

When setting multiple groups, set [RESPONSE(ID ALL)] to [ON] in only one projector in each group.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DX610EL Seite 122

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-DX610EL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info