Bedienungsanleitung Panasonic PT-DZ10KE (Seite 140 von 187) (Englisch)

511533

140

Zoom out

Zoom in

Vorherige Seite

1/187

Nächste Seite

Chapter 4 Settings — [NETWORK] menu

140 - ENGLISH

Error information page

When [Error (Detail)] or [Warning (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the

error/warning details.

f The projector may go into the standby status to protect the projector depending on the contents of the error.

1 Self-diagnosis result display

Displays the item check results.

[OK]:

Indicates that operation is normal.

[FAILED]:

Indicates that there is a problem.

[WARNING]:

Indicates that there is a warning.

r [FAILED] items displayed when a problem occurs

Parameter Description

[MAIN CPU BUS] There is a problem with the microcomputer circuitry. Consult your dealer.

[FAN] There is a problem with the fan or the fan drive circuit. Consult your dealer.

[INTAKE AIR TEMPERATURE]

The air intake temperature is too high. The projector may be used in an operating

environment where the temperature is high, such as near a heating appliance.

[OPTICS MODULE TEMPERATURE]

The temperature around the optics module inside the projector is high. The projector

may be used in an operating environment where the temperature is high, such as near a

heating appliance.

[AROUND LAMP TEMPERATURE] The temperature around the lamp is high. The air exhaust port may be blocked.

[LAMP1 REMAIN TIME] The runtime of the lamp has exceeded the specied time, and it is time to replace the

lamp.

[LAMP2 REMAIN TIME]

[LAMP1 STATUS] The lamp has failed to turn on. Wait a while until the luminous lamp cools off, and then

turn on the power.

[LAMP2 STATUS]

[APERTURE(CONTRAST-SHUTTER)] There is a problem in the contrast shutter circuit for dynamic iris. Consult your dealer.

[INTAKE AIR TEMP.SENSOR]

There is a problem with the sensor used to detect intake temperature. Consult your

dealer.

[OPTICS MODULE TEMP.SENSOR]

There is a problem with the sensor used to detect temperature inside the projector.

Consult your dealer.

[AROUND LAMP TEMP. SENSOR]

There is a problem with the sensor used to detect exhaust air temperature. Consult your

dealer.

[BATTERY] Battery replacement is required. Consult your dealer.

[LENS MOUNTER] There is a problem in the lens mounter. Consult your dealer.

[COVER OPEN]

Installation of the lamp unit cover is incomplete. Check the installation of the lamp unit

cover. (x page 161)

[BRIGHTNESS SENSOR]

There is a problem with the luminance sensor. If problems persist even after switching

on the power, consult your dealer.

[ANGLE SENSOR] There is a problem with the sensor that detects angle. Consult your dealer.

[FILTER UNIT]

The air lter unit is not attached. Check the connection of the air lter unit.

(x page 157)

[AIR FILTER]

There is too much dust accumulated in the air lter unit. Turn the <MAIN POWER>

switch <OFF> (x page 55), and clean the air lter. (x page 157)

[AC POWER]

AC input voltage is weak. Use electric wiring that can sufciently withstand the power

consumption of the projector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DZ10KE Seite 140

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-DZ10KE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info