Bedienungsanleitung Panasonic PT-DZ16KU (Seite 142 von 176) (Englisch)

598886

142

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

Chapter 5 Maintenance — Lamp/temperature/lter indicators

142 - ENGLISH

Temperature indicator <TEMP>

Indicator status Lighting in red

Blinking in red

(2 times)

Blinking in red

(3 times)

Status Warm-up status

Internal temperature is high

(warning).

Internal temperature is high

(standby status).

The cooling fan has

stopped.

Cause

f Did you turn on the power

when the temperature

was low (around 0 °C

(32 °F))?

f Is the air intake/exhaust port blocked?

f Is the room temperature high?

f Is the lter indicator <FILTER> lit?

―

Solution

f Wait up to 20 minutes in

the current status.

f Install the projector in a

location with the operating

environment temperature

between 0 °C (32 °F) and

45 °C (113 °F)

f Remove any objects that are blocking the air intake/

exhaust port.

f Install the projector in a location with the operating

environment temperature between 0 °C (32 °F) and

45 °C (113 °F)

, and ambient humidity between 20 %

and 80 % (no condensation).

f Do not use the projector at high altitudes of 2 700 m

(8 858') or higher above sea level.

f Clean or replace the air lter unit. (x page 143)

f Turn the <MAIN POWER>

switch to <OFF>

(x page 50), and

consult your dealer.

*1 When using the projector at high altitudes (between 1 400 m (4 593') and 2 700 m (8 858') above sea level), the operating environment temperature

should be between 0 °C (32 °F) and 40 °C (104 °F).

If you use the smoke cut lter, the operating environment temperature should be between 0 °C (32 °F) and 35 °C (95 °F). However, it cannot be

used at high altitudes.

Note

f If the temperature indicator <TEMP> is still lit or blinking after taking the measures, ask your dealer for repair.

Filter indicator <FILTER>

Indicator status Lighting in red Blinking in red

Status

The lter is clogged.

The temperature inside or outside the projector is abnormally high.

The air lter unit is not

attached.

Cause f Is the air lter unit dirty?

f Is the air intake/exhaust

port blocked?

f Is [HIGH ALTITUDE

MODE] set correctly?

f Is the air lter unit

attached?

Solution

f Clean or replace the air

lter unit. (x page 143)

f Remove any objects that

are blocking the air intake/

exhaust port.

f When using the projector

at high altitudes between

1 400 m (4 593') and

2 700 m (8 858'), set

[HIGH ALTITUDE MODE]

(x page 96) to [ON].

f Do not use the projector

at high altitudes of

2 700 m (8 858') or higher

above sea level.

f Attach the air lter unit.

Note

f If the lter indicator <FILTER> is still lit or blinking after taking the measures, ask your dealer for repair.

f If the lter is clogged while [LAMP SELECT] is set to [QUAD] or [TRIPLE], the setting may be forcibly changed to [DUAL]. To reset the

setting, clean the air lter unit or replace it with a new one.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DZ16KU Seite 142

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info