Bedienungsanleitung Panasonic PT-DZ21KE (Seite 101 von 179) (Englisch)

511534

101

Zoom out

Zoom in

Vorherige Seite

1/179

Nächste Seite

[PROJECTOR SETUP] menu

ENGLISH - 101

Settings

Note

For a set time after [LAMP SELECT] is switched,

[LAMP SELECT] cannot be switched again,

because the speed of the lamp replacement cycle

will increase. Repeatedly switching [LAMP SELECT]

in a short time will also increase the speed of the

lamp replacement cycle.

The colors of the items indicate the status.

Green → Current setting

Yellow → Current setting

(When there is a lamp that cannot turn on or failed

to turn on)

Red → Lamp that has failed to turn on

White → Any other status

When a lamp fails to turn on or has been used in

excess of 2 000 hours and a setting other than

[QUAD] is selected, that lamp is turned off and

another lamp turned on.

When a lamp fails to turn on or has been used in

excess of 2 000 hours in [QUAD], a lamp that has

not been used in excess of 2 000 hours is turned

on.

The projector enters standby mode when all lamps

have been used in excess of 2 000 hours.

Ensure that lamp units not to be turned on are also

installed.

More lamps than the specied number of lamps

light temporarily to prevent decreased illuminance

when a lamp is switched.

[LAMP RELAY]

The lump to be turned on can be automatically

switched by setting a day and time.

The degradation of the lamp due to continuous usage

can be reduced by automatically switching the lamp

to be turned on when using the projector continuously

for a week or more.

1) Press



to select [LAMP RELAY].

2) Press

󱚣󱚤

to switch [LAMP RELAY].



The time setting to switch the lamp will change

as follows each time you press the button.

[OFF] [24H] [1WEEK]

3) Press



to select [TIME].

4) Press the <ENTER> button.



Enters adjustment mode (the display is

blinking).

5) Press

󱚣󱚤

to select [HOUR] or

[MINUTE], and then press



adjust it.

(1 hour or 1 minute increments)

[00:00] [00:01] [00:59]

6) Press the <ENTER> button.



The adjusted time is established.

7) Press



to select [DAY OF THE

WEEK].

8) Press

󱚣󱚤

to switch [DAY OF THE

WEEK].



The setting will change as follows each time

you press the button.

[SUNDAY] [MONDAY] [TUESDAY]

[WEDNESDAY]

[SATURDAY] [FRIDAY] [THURSDAY]

Note

The [LAMP RELAY] function is enabled when

[SINGLE], [DUAL], [TRIPLE], or [QUAD] is selected

in [LAMP SELECT].

When [SINGLE] or [DUAL] is selected in [LAMP

SELECT], the lamp switches to the specied time.

When [TRIPLE] is selected in [LAMP SELECT], the

lamp switches a total of three times every two hours

from the specied time, and thereafter maintains

the previous status until the specied time.

When [QUAD] is selected in [LAMP SELECT],

three turn on at the specied time and the three

lamps switch every two hours for a total of four

times. Next, four lamps turn on eight hours after the

specied time and thereafter three lamps switch

again after the specied time.

The operating time will be the local time. (



page 110)

Use the number (<0> to <9>) buttons on the remote

control to directly enter the time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DZ21KE Seite 101

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-DZ21KE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info