Bedienungsanleitung Panasonic PT-EW530E (Seite 67 von 118) (Englisch)

511541

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

Setting

ENGLISH -

Settings

Power management

For reducing power consumption as well as

maintaining the lamp life, the Power management

function turns off the projection lamp when the

projector is not operated for a certain period.

Press ▲▼ to select [Power 1 )

management].

Press ► or the <ENTER> button to 2 )

access the submenu.

Mode

Press ▲▼ and then press the 1 )

<ENTER> button to select one mode

among the items as below.

Ready

When the lamp has been fully cooled

down, the <ON(G)/STANDBY(R)>

indicator changes to green blinking.

In this condition, the projection lamp

will be turned on if the input signal

is reconnected or any button on

the side control or remote control is

pressed.

Shut

down

When the lamp has been fully cooled

down, the power will be turned off.

Off

[Power management] function is off.

Timer

Press ▲▼ to select [Timer] and then 1 )

press the <ENTER> button.

Press ▲▼ to set the Timer(1~30min).2 )

Standby mode

This function can set the electric power when the

projector is standing by.

Press ▲▼ to select [Standby mode] 1 )

and then press the <ENTER> button.

Press ▲▼ to switch between the items 2 )

as below.

Normal

The normal situation.

Eco

The power less than 0.5W.

Network

The power less than Normal.

Note

When selecting [Network], the cooling fans may be

running depending on the temperature inside the

projector even if the projector is turned off.

If [Standby mode] is set to [Eco], you cannot use network

functions when the projector is standing by. Also, you

cannot use some RS-232C protocol commands.

If set to [Network], you can use network functions when

the projector is standing by.

Direct on

Press ▲▼ to select [Direct on] and 1 )

then press the <ENTER> button.

Press ▲▼ to switch between [On] and 2 )

[Off].

When this function is set to [On], the projector

will be automatically turned on just by

connecting the AC power cord to a wall outlet.

Be sure to turn off the projector properly. If the

projector is turned off in the incorrect sequence,

the [Direct On] function does not work properly.

P-timer

This function allows you to change the setting of the

P-timer and execute it.

Press ▲▼ to select [P-timer].1 )

Press ► or <ENTER> button to access 2 )

the submenu.

Mode

Press ▲▼ button to select one mode 1 )

among the items as below.

Count up

The P-timer display 000:00

appears on the screen and the

count up starts (000:00-180:00).

Count down

The time set in the Timer setting

appears on the screen and the

countdown starts.

Timer

Press ▲▼ to select [Timer] and then 1 )

press the <ENTER> button.

Press▲▼ to set the [Timer](1-180 Min).2 )

[Timer] is available in [Count down] only.

Factory default value is 10 Min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-EW530E Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-EW530E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info