Bedienungsanleitung Panasonic PT-EX16KU (Seite 34 von 108) (Englisch)

543734

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Powering on/off

34 - ENGLISH

Basic Operation

Powering off the projector

Power <ON/STAND-BY>

button

Control panel Remote control

Power <STAND-BY>

button

1) Press the power <ON/STAND-BY>

button on the control panel or the

power <STAND-BY> button on the

remote control.

■

[Power off ?] is displayed on the screen.

■

The screen display will disappear when any button

other than the power <ON/STAND-BY> button on

the control panel and the power <STAND-BY>

button on the remote control is pressed or when

approximately four seconds elapse.

2) Press again the power <ON/STAND-

BY> button on the control panel or

the power <STAND-BY> button on the

remote control.

■

The lamp goes off and the projection stops.

■

The power indicator <POWER> goes off while

the cooling fan continues to rotate, and the

standby indicator <STAND-BY> ashes.

3) When the standby indicator <STAND-

BY> comes on, press the

< >

side of the

main power switch to turn off the power.

Note

Do not turn on the power immediately after turning it off.

In the cooling state of the luminous lamp after the

power is turned off, the lamp may not light up even

when the power is turned on. In this case, wait for

the standby indicator <STAND-BY> to turn red, and

then turn on the power again. Turning on the power

while the lamp is still hot may shorten the lamp life.

When you turn off the power using the power <ON/

STAND-BY> button on the control panel or the

power <STAND-BY> button on the remote control

with the main power switch on the projector body

turned on, the projector continues to consume

electricity. For details on power consumption, refer

to “Power consumption” (



page 102).

Check that key lock is off in the [Security] menu.

(



page 69)

If you use the projector for longer than 24 hours,

turn off the power every 24 hours and wait for one

hour. This will increase the lamp life.

Direct power off function

You can disconnect the power cord, turn off the power

by the power breaker switch, etc. without pressing the

power <STAND-BY> button on the remote control or

the main power switch on the projector.

This is useful in cases where the switch is not easily

accessible, such as when the projector is ceiling

mounted. This function also provides safety if a power

outage occurs or if the power cord is accidentally

disconnected from the outlet immediately after turning

off the power.

Note

When the lamp has been cooled by the direct

power off function, it sometimes takes longer than

usual for the lamp to light up again.

Power management function

The projector has a power management function. If no

signal is detected for 30 seconds and no operation is

performed on the projector, [No signal] and the timer

appear on the screen and a countdown starts.

If the countdown is completed without a signal being

input or an operation on the projector, this function

works to save power and extend the service life of the

lamp.

Note

The factory default setting is [Off]. For details, refer

to [Power management] (



page 68).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-EX16KU Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-EX16KU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info