Bedienungsanleitung Panasonic PT-EX500E (Seite 40 von 118) (Englisch)

511543

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

- ENGLISH

Basic Operation

Projecting

Check the connections of the peripheral devices and connection of the power cord (

page 35) and switch on the

power (

page 37) to start the projector. Select the image and adjust the state of the image.

Selecting the image

Select an input signal.

Side Control/Remote Control Operation

You can press the <INPUT> button on the side control or the remote control to select INPUT 1/2/3 as input

source.

Remote Control Operation

Press the <INPUT 1>, <INPUT 2>, or <INPUT 3> button on the remote control. Each time you press the <INPUT

1/2/3> button, the input signal will be changed.

Attention

Images may not be projected properly depending on the connected device and DVD, video tape, etc. to be played. Select a

system format that is suitable for the input signal [Y, Pb/Cb, Pr/Cr ] or [RGB] in the [Input] menu (

page 49).

Check the aspect ratio of the screen and the image and select the optimum aspect ratio under the [Screen] menu

(

page 58).

Adjusting the image

Adjusting the position of the lens

Press the <LENS SHIFT> button on the remote control or the <LENS> button on the side control.1 )

[Lens shift] is displayed on the screen for four seconds.

While the display appears, press ▲▼2 )

◄►

to move the image horizontally and vertically.

As you move the image, there is a certain position at which the arrows pointing up, down, left and right turn red. This

position is the center for the lens.

At positions of maximum shift, the arrows disappear.

The projector stores the setting made using the lens shift function when the power is turned off.

When the position of the image is shifted, the image may become a little darker.

Press and hold the <LENS> button or <LENS SHIFT> button for more than 5 seconds, the lens shift will be return to the

center position.

The gure below shows an example of when the standard lens is attached.

* When it is 60%, it is only for EZ570 series, EW630 series and

EW530 series. When it is 50%, it is only for EX600 series and

EX500 series.

Adjusting the zoom and focus

Press the <ZOOM +/-> button and the <FOCUS +/-> button on the remote control.1 )

[Zoom] and [Focus] are displayed on the screen for four seconds.

While the display appears, press ▲▼ to adjust the zoom and focus.2 )

Note

When [Display] is set to [Off], the adjustment screen will not appear.

It is recommended that the images are projected continuously for at least 30 minutes before the focus is adjusted.

The display position can be

shifted upward up to 60%*

elevation of the display.

When the lens is shifted to top. When the lens is shifted to bottom.

When the lens is shifted to leftmost.

When the lens is shifted to rightmost.

The display position can be

shifted downward up to 60%*

low level of the display.

The display position can be

shifted to the left in up to

10% width of the display.

The display position can be

shifted to the right in up to

10% width of the display.

Lens shift



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-EX500E Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-EX500E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info