Bedienungsanleitung Panasonic PT-VX500E (Seite 52 von 98) (Englisch)

511583

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

Setting

- ENGLISH

Settings

Logo PIN code change

Logo PIN code can be changed to your desired four-

digit number.

Press ▲▼ to select [Logo PIN code 1 )

change] and press the <ENTER>

button.

Current logo PIN code dialog box appears.

Press ▲▼ to enter the current code, 2 )

press the ► button to x the number

and move the red frame pointer to the

next box.

The New Logo PIN code input dialog box

appears.

Repeat this step to set the new Logo 3 )

PIN code.

Attention

Be sure to note the new Logo PIN code and keep it on

hand. If you lost the number, you could no longer change

the Logo PIN code setting.

HDMI setup

This function is only used for HDMI input source.

Press ▲▼ to select [HDMI setup].1 )

Press ► or the <ENTER> button.2 )

The names for the output setting of Digital R/G/

B vary from equipment to equipment.

Image

Normal When the output of Digital R/G/B

equipment is set to Standard.

Enhanced When the output of Digital R/G/B

equipment is set to Enhanced.

Sound

HDMI

When Digital input source is input,

Sound is set to HDMI.

Computer

When DVI input source is changed

to HDMI input source, Sound is set

to Computer 2.

Attention

For details, refer to the operating instructions of your

Digital R/G/B equipment.

Connect the computer 2 audio input signals to

COMPUTER AUDIO IN 1 terminal as Sound function is

set to Computer 2 and MIC function is turned on.

Terminal

The COMPUTER 2 IN/MONITOR OUT terminal on

the back of the projector is switchable for computer 2

input or monitor output.

Press ▲▼ to select [Terminal] and 1 )

then press the <ENTER> button.

Press ▲▼ to switch the item.2 )

Computer 2 Computer input

Monitor out Monitor out

Note

Terminal function is not available when selecting

[Computer 2] to the input source. Change the input

source to the others (HDMI, Computer 1, Video or

S-Video) so that the Terminal function will be available.

Power management

For reducing power consumption as well as

maintaining the lamp life, the Power management

function turns off the projection lamp when the

projector is not operated for a certain period.

Press ▲▼ to select [Power 1 )

management].

Press ► or the <ENTER> button to 2 )

access the submenu.

Mode

Press ▲▼ and then press the 1 )

<ENTER> button to select one mode

among the items as below.

Ready When the lamp has been fully cooled

down, the <ON(G)/STANDBY(R)>

indicator changes to green blinking.

In this condition, the projection lamp

will be turned on if the input signal

is reconnected or any button on the

control panel or remote control is

pressed.

Shut

down

When the lamp has been fully cooled

down, the power will be turned off.

Off [Power management] function is off.

Timer

Press ▲▼ to select [Timer] and then 1 )

press the <ENTER> button.

Press ▲▼ to set the Timer(1~30min).2 )

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-VX500E Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-VX500E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info