Bedienungsanleitung Panasonic RXD50EG (Seite 7 von 28) (Englisch, Spanisch, Polnisch)

608288

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISHESPAÑOL

RQTX1041

Cassette tape – Play and record

Basic play Basic play

Use normal position tapes.

High position and metal position tapes can be played, but the unit will not be

able to identify the characteristics of these tapes.

1 Press [TAPE/OFF].

2 Open the cassette operation buttons’ lid.

3 Press [8/x, STOP/EJECT] and insert the cassette.

Insert with the side to be played facing up and the exposed tape facing

towards you. Close the deck by hand.

4 Press [4, PLAY] to start play.

Stop tape

playback

Press [8/x, STOP/EJECT].

Pause play

Press [9, PAUSE].

Press again to resume play.

Fast-forward

and rewind

Press [3, REW/REV] or [5, FF/CUE] in the stop

mode.

Search for a

speciﬁ c point

Press [3, REW/REV] (to search backward) or

[5, FF/CUE] (to search forward) during playback.

Play is resumed when the button is released.

Recording Recording

Use normal position tapes.

High position and metal position tapes can be used, but the unit will not be able

to record or erase them correctly.

✒

Preparation

Wind up the source tape so recording can begin immediately.

1 Press [0, STOP/EJECT] and insert the cassette to be recorded.

Insert with the side to be recorded facing up and the exposed tape facing

towards you.

2 Select the source to be recorded.

RX-D55

USB

Prepare the USB mass storage device for recording

(Z page 6).

Radio

Tune in the station (Z page 6).

Disc

1. Insert the disc you want to record.

Press [4/9, CD] and then [8] (stop).

2. Prepare the desired disc recording mode.

Record programmed tracks

Program the tracks you want (Z page 5).

Record speciﬁ c albums or tracks

Press [PLAY MODE] to select the desired mode

(Z page 5).

Music port

Select music port (Z page 8).

3 Press [

] to start recording.

Stop recording

Press [8/x, STOP/EJECT].

Record on the other

side of the tape

Turn the cassette over and press [

Erase a recorded

sound

1. Press [TAPE/OFF].

2. Insert the recorded cassette.

3. Press [

✒

Note

Changes to volume and sound quality do not affect recording.

Erasure prevention

The illustration shows how to remove the tabs to prevent recording. To record on

the tape again, cover as shown.

Side A

Tab for Side ATab for Side B

To prevent recording

Adhesive tape

To re-record

✒

Note

• Tapes exceeding 100 minutes are thin and can break or get caught in the

mechanism.

• Tape slack can get caught up in the mechanism and should be wound up

before the tape is played.

• Endless tapes can get caught up in the deck’s moving parts if used incorrectly.

Using the clock and timers

Setting the clock Setting the clock

This is a 24-hour clock.

1 Press [CLOCK/TIMER].

Each time you press the button:

Original display

PLAY ON

CLOCK

2 Within 5 seconds or so

Press [2/3] or [5/6] to set the time.

Holding down the button will speed up the time selection.

3 Press [CLOCK/TIMER] to ﬁ nish setting the time.

Displaying the clock

Press [CLOCK/TIMER] to display the clock for few seconds.

✒

Note

• Reset the clock regularly to maintain accuracy.

• When the unit is in standby mode and it is powered by batteries, clock will not

be displayed.

Using the play timer Using the play timer

You can set the timer to come on at a certain time to wake you up.

✒

Preparation

• Turn the unit on and set the clock.

• Prepare the music source you want to listen to; disc, radio, USB (

RX-D55

only)

or music port source, and set the volume.

1 Press [CLOCK/TIMER] repeatedly to select the play timer.

2 Within 5 seconds or so

Press [2/3] or [5/6] to set the

starting time.

3 Press [CLOCK/TIMER] to conﬁ rm.

4 Repeat steps 2 and 3 to set the ﬁ nishing

time.

To activate the timer

5 Press [# PLAY] to turn on the timer.

# PLAY

No display (off)

6 Press [TAPE/OFF] to turn off the unit.

Change the

settings

Repeat steps 1 to 4 and 6 (Z see above).

Change the source

or volume

1. Press [# PLAY] to clear the timer indicator from the

display.

2. Make changes to the source or volume.

3. Perform steps 5 and 6 (Z see above).

Check the settings

(when the unit is on

or in standby mode)

Press [CLOCK/TIMER] repeatedly to select # PLAY

(there is no display when the unit is powered by

batteries and is in standby mode).

Cancel

Press [# PLAY] to clear the timer indicator from the

display.

✒

Note

• The play timer will start at the preset time, with the volume increasing

gradually to the preset level.

• The timer comes on at the set time every day if the timer is on.

• The unit must be in the standby mode for the timer to function.

• If you turn the unit off and on again while a timer is functioning, the ﬁ nish time

setting will not be activated.

Using the sleep timer Using the sleep timer

This function enables you to turn off the unit automatically after the set time

except in tape mode.

Press [SLEEP] repeatedly to select your desired time (in minutes).

To cancel

Press [SLEEP] repeatedly to select “OFF”.

Changing the remaining time

Press [SLEEP] to show the remaining time, and press [SLEEP] again to select

your desired time.

✒

Note

• The play and sleep timer can be used together.

• The sleep timer always has priority. Be sure not to overlap timer settings.

RQTX1041-2Z_1gb.indd 7RQTX1041-2Z_1gb.indd 7 4/8/2010 2:23:14 PM4/8/2010 2:23:14 PM

Panasonic RXD50EG Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic RXD50EG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info