Bedienungsanleitung Panasonic SA-XR700 (Seite 25 von 52) (Englisch)

502462

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

RQT8739

When one of the following error messages appears, press [TEST, –AUTO] to cancel and perform the auto speaker setup again.

•

You can also perform automatic speaker detection only (

page 10).

• Speaker placement, speaker directions and other conditions

may prevent correct setting.

• The unit sets the lowpass filter frequency at the value of the

speaker capable of reproducing the lowest frequency signal

among speakers judged as “SMALL”.

•

When left and right speakers differ in size, they are set as “SMALL”.

• When surround speakers and surround back speakers differ in

size, they are set as “SMALL”.

• Left and right front speakers are set as “LARGE

” even if their

size is “SMALL” when you perform the auto speaker setup

without connecting the subwoofer.

• Only level is adjusted for the subwoofer.

• Ez Sync HDAVI Control (á page 13) does not work during the

auto speaker setup.

•

The selection switches automatically to “SPEAKERS A” only

when you perform the auto speaker setup without selecting

“SPEAKERS A”.

•

The auto speaker setup is unavailable while muting (

page 31) is on.

• The unit sets at 45 feet (15 meters) the distance of speakers

located more than 45 feet (15 meters) away from the seating

area. The set distance is displayed as “OVER ” (á page 35).

• Speakers whose polarity was automatically adjusted are

displayed with “– ” such as “L 10.0 – ” (á page 35).

•

Speaker settings made with the setup microphone are canceled

when you perform automatic speaker detection (

page 10).

When the “AUTO SPEAKER SETUP” indicator is off

after the auto speaker setup:

Auto speaker settings have been canceled as a result of

various setting changes.

Speaker size

• LARGE: Speakers that can sufficiently reproduce the bass

range down to 20 Hz.

• SMALL: Speakers that do not satisfy the requirements for

LARGE speakers.

You can perform steps instructed in “Setting speakers and their

sizes” (á page 35) to change speaker sizes set automatically.

Lowpass filter

When the speaker size is “SMALL”, the unit cannot sufficiently

reproduce the bass range.

You can set the lowpass filter frequency according to the

playback frequency range and arrange the unit to output the

missing bass range from the subwoofer.

With the setup microphone, the unit automatically sets the following.

STEP1

STEP2

STEP3

DISTANCE : The unit measures the distance between each speaker and the seating area and corrects the sound delay

in the seating area. The maximum speaker distance for correcting the delay is 45 feet (15 meters).

POLARITY : The unit checks the polarity of each speaker and, when the polarity is wrong, corrects it.

Select “CHECK NO ” in “Setting the unit against automatic polarity adjustment” (á page 36) before starting the auto

speaker setup when you do not want the unit to adjust polarity automatically.

SIZE / FREQUENCY : The unit measures acoustic characteristics of the room including speaker characteristics (size

and lowpass filter settings) and adjusts them.

LEVEL : The unit checks the output level of each speaker and makes adjustment.

Error messages

Message Cause Countermeasure

• The setup microphone is not connected. • Connect the setup microphone properly.

•

The setup microphone does not catch test signals.

• Check if the microphone is placed properly.

• Loud noise is preventing measurement.

• Perform the auto speaker setup again when the

room is quiet.

• Turn off an air-conditioner and other equipment

that are producing noise.

• A speaker is too far.

• An error occurred from an unknown cause.

• Check speaker locations.

• Perform the setup again.

• The right surround back speaker was detected,

but the left surround back speaker was not

detected.

•

Connect to the left surround back speaker terminal

when you connect only one surround back speaker.

•

Check the left surround back speaker’s connections.

• Surround back speakers were detected, but left

and right surround speakers were not detected.

• Connect surround speakers as well when you

connect surround back speakers.

• Unable to detect one or both of the two surround

speakers

• Check connections.

• Unable to detect one or both of the two front

speakers

• Check connections.

• Test signals from the speakers are too weak to

allow accurate measurement with the

microphone.

•

Change the microphone location (height, direction etc.).

• Check if there is any obstacle near a speaker that

is blocking the test signals.

•

Set the subwoofer volume to the normal listening level.

Note

Auto speaker setup using the setup microphone

Basic operations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SA-XR700 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SA-XR700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info