Bedienungsanleitung Panasonic sc ak 44 (Seite 4 von 32) (Englisch)

158694

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Before using

RQT5621

Before using this unit please read these operating instructions carefully.

Take special care to follow the warnings indicated on the unit itself as

well as the safety suggestions listed below.

Afterwards keep them handy for future reference.

Safety

1. Power Source —The unit should be connected to power supply

only of the type described in the operating instructions or as

marked on the unit.

2. Polarization—If the unit is equipped with a polarized AC power

plug (a plug having one blade wider than the other), that plug will

fit into the AC outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try reversing the

plug. If the plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of

the polarized plug.

3. Power Cord Protection—AC power supply cords should be

routed so that they are not likely to be walked on or pinched by

items placed upon or against them. Never take hold of the plug

or cord if your hand is wet, and always grasp the plug body

when connecting or disconnecting it.

4. Nonuse Periods—When the unit is not used, turn the power off.

When left unused for a long period of time, the unit should be

unplugged from the household AC outlet.

Installation

Environment

1. Outdoor Antenna Grounding—If an outside antenna is con-

nected to the receiver, be sure the antenna system is grounded

so as to provide some protection against voltage surges and

built-up static charges. Section 810 of the National Electrical

Code, ANSI/NFPA No. 70-1990, provides information with re-

spect to proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit, size

of grounding conductors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for the

grounding electrode. See figure below.

3. Heat—The unit should be situated away from heat sources such

as radiators and the like.

It also should not be placed in temperatures less than 5°C (41°F)

or greater than 35°C (95°F).

4. Condensation—Moisture may form on the lens in the following

conditions...

•

immediately after a heater has been turned on.

•

in a steamy or very humid room.

•

when the unit is suddenly moved from a cold environment to a

warm one.

If moisture forms inside this unit, it may not operate properly. To

correct this problem, turn on the power and wait about one hour

for the moisture to evaporate.

Placement

1. Ventilation—The unit should be situated so that its location or

position does not interfere with its proper ventilation. Allow 10

cm (4

) clearance from the rear of the unit.

2. Foreign Material—Care should be taken so that objects do not

fall into and liquids are not spilled into the unit. Do not subject

this unit to excessive smoke, dust, mechanical vibration, or shock.

3. Magnetism—The unit should be situated away from equipment

or devices that generate strong magnetic fields.

4. Stacking—Do not place heavy objects, other than system com-

ponents, on top of the unit.

5. Surface—Place the unit on a flat, level surface.

6. Carts and Stands—The unit should be used only

with a cart or stand that is recommended by the

manufacturer.

The unit and cart combination should be moved

with care. Quick stops, excessive force, and un-

even surfaces may cause the unit and cart combination to over-

turn.

7. Wall or Ceiling Mounting—The unit should not be mounted to

a wall or ceiling, unless specified in this operating instructions.

Maintenance

(See page 30 for details.)

Clean the cabinet, panel and controls with a soft cloth lightly moist-

ened with mild detergent solution.

Do not use any type of abrasive pad, scouring powder or solvent

such as alcohol or benzine.

Service

1. Damage Requiring Service —The unit should be serviced by

qualified service personnel when:

(a) The AC power supply cord or the plug has been damaged; or

(b) Objects have fallen or liquid has been spilled into the unit; or

(d) The unit does not appear to operate normally or exhibits a

marked change in performance; or

(e) The unit has been dropped, or the enclosure damaged.

2. Servicing —The user should not attempt to service the unit

beyond that described in the operating instructions. All other

servicing should be referred to an authorized service personnel.

For the address of an authorized servicenter:

In the U.S.A., call 1-800-211-7262, e-mail

consumerproducts@panasonic.com, or visit

www.panasonic.com

In Canada, call 905-624-5505 or visit www.panasonic.ca

2. Water and Moisture—Do not use this unit near water—for ex-

ample, near a bathtub, washbowl, swimming pool, or the like.

Damp basements should also be avoided.

ANTENNA LEAD

IN WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

NEC–NATIONAL ELECTRICAL CODE

PRECAUTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic sc ak 44 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic sc ak 44

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info