Bedienungsanleitung Panasonic SC-BT300 (Seite 51 von 60) (Englisch)

602096

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

RQT9508

Messages

The following messages or service numbers appear on the TV or unit’s display when something unusual is detected during startup and use.

On the TV Page

Cannot play. ≥You inserted an incompatible disc (Discs recorded in PAL video, etc.). 42, 43

Cannot display on this unit. ≥You tried to play a non-compatible image. 43, 44

No disc is inserted. ≥The disc may be upside down. —

$ This operation is not

available.

≥Some operations are prohibited by the unit or disc. For example;

– [BD-V]

: During play back, reverse slow-motion or reverse frame-by-frame is not possible.

—

$ This operation is prohibited

by this disc.

≥Depending on the disc, you may not be able to perform search or skip when film previews

and warning screens are being played back.

—

Cannot connect.

Please check the connection of

the LAN cable.

≥When a hub is used but its Link lamp does not light up, check the cable connection, LAN

terminal connection, cable itself (a cross cable may be used by mistake), etc.

IP address is not set. ≥The “IP Address” in “IP Address/DNS Settings” is “---. ---. ---. ---”. Set the “IP Address”,

“Subnet Mask”, and “Default Gateway”. (Select the automatic address acquisition if

necessary.)

Cannot obtain IP address using

DHCP.

Please check the connection or

router settings.

≥If you use a hub, then check the connection between the hub and the router.

– Use the UPLINK port of the hub to connect to a router.

– Check whether or not the hub’s Link lamp lights up. If it does not light up, then check the

cable connection, LAN terminal connection, cable itself (a cross cable may be used by

mistake), etc.

≥If the above conditions are OK, then the router may not operate in DHCP mode. Check the

router settings and operation. You may reset the router to restore it to normal.

This IP address is already in

use.

Please check the IP address

setting.

≥This unit’s IP address is used by another device. Check the IP addresses of this unit,

personal computers, and routers, etc. If necessary, reconfigure them to avoid IP

addresses from being duplicated.

—

Unable to perform Connection

Test.

Please try again.

≥Turn the unit off. Remove the power cord and reconnect it and try again. If the same

symptom persists, then consult your dealer.

—

IP address not set correctly.

Connection Test was

unsuccessful. No reply

from host.

Please check the connection or

router settings.

≥If you use a hub, then check the connection between the hub and the router.

– Use the UPLINK port of the hub to connect to a router.

–If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal

connection, cable itself (a cross cable may be used by mistake), etc.

≥Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP Address/DNS

Settings”.

≥If the MAC address information is required, then press [SETUP] to display the “Network”

menu.

Network connection refused.

Please confirm Setup “BD-Live

Internet Access.”

≥When you set “BD-Live Internet Access” to “Allow ( Limited )” and play BD-Live contents

which do not have a content owner certificate, the Internet access of the content is not

allowed. If you allow the content to connect to Internet, set “BD-Live Internet Access” to

“Allow ( ALL )”.

Unable to check for latest

firmware version.

Please try again later.

≥The firmware download server is currently unavailable. Please try again later.

—

High Clarity Sound is effective.

Analog video output is turned

off when

playback starts.

≥“High Clarity Sound” in setup menu is set to “Enable”, and “High Clarity Sound” in

on-screen menu is set to “On”.

36, 38

No Video ≥Depending on the connected iPod, video menu may not be available on the TV. Select the

iPod menu (iPod LCD) mode and operate video playback from your iPod menu.

On the unit’s display

F99 ≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to

standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.

—

HDMI ONLY ≥Some BD-Video discs can only be output with HDMI. —

NET ≥Displays while VIERA CAST is starting up. —

No PLAY ≥There is a viewing restriction on a BD-Video or DVD-Video. 37

No READ ≥The media is dirty or badly scratched. The unit cannot play. —

PLEASE WAIT ≥The unit is carrying out internal process.This is not a malfunction. You cannot operate the

unit while “PLEASE WAIT” is displayed.

≥When connected to a TV (VIERA) with HDAVI Control 4, and power supply is turned off by

the “Auto power stand-by” function on the TV side.

—

SET 

(“  ” stands for a number.)

≥The remote control and main unit are using different codes. Change the code on the

remote control.

Press and hold [OK] and the indicated number button at the same

time for more than 5 seconds.

UNFORMAT ≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or

DVD-RW (DVD-Video format).

—

UNSUPPORT ≥You have inserted a media the unit cannot play. 42, 43

Reference

BT300.book 51 ページ２００９年６月１２日　金曜日　午後１２時１３分

Panasonic SC-BT300 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info